RB19KN-3A (CG60A) Magic Chef Refrigerator - Instructions

I watched the repair video on the web site a couple of times just to get comfortable with what to expect. (i.e. pressing tabs on wiring harness to remove, placement of lift arm for removal and installation) These instructions were a big help...I had the removal, modifications and installation completed in less than 30 minutes. Ice cubes (without the extra icicles) in 1 hour...

I have a Maytag Refridgerator with lower freezer and ice maker. Stopped making ice. Noticed the unit would fill up and freeze but the tray wouldn't rotate to drop the cubes into the tray. Cleared the frozen trays to see if it was just stuck but same thing happened. Replaced unit, not difficult with the exception that the top tray is ridiculously hard to get out. Never did do it, just worked around it. Working perfect now.

ordered a new shut-off valve. arrived in 5 days. installation had to wait a couple more day for i had to order a new compression nut. the reason i had to order a new nut was because the original nut was made of teflon and stripped easily when i tightened it to make a leak proof.joint. the new nut arrived in two days and was installed readily being that it was made of brass and consequently did not strip when i tightened to make a drip proof joint. finished in approximately twenty minutes' the video that this site has on the internet was of great value.

I watched the video regarding the instillation of this ice maker a few times and then followed it exactly. It was incredibly easy. We had ice cubes about two hours later and no longer had a leak making icebergs!

First i used a nut driver to remove the bottom screw, the unclipped the two top clips by leaningthe bottom of the unit outwards. I used a mirror to see the two top clips as i could not see inside. Then i removed the wiring harness from the refrigerator. The unit came right out, i transerred the needed parts, and re-installed. Not too bad - about 45 mins. It works great!

Removed the elec connection (after unplugging app) found it easier to remove from appliance. Remove the three screws ( do not temove,....just loosen, the top two) bottom must be removed! Insert the power connection, exchange the tilt up rod, line up the water connection and place back on the two top screws. Tighten and relpace the bottom screw. I found out the hard way.... you cant't see the two top screws . The slots on the ice maker just fit over the screw heads.... it's cold in there!!!

Hopoe this helps..

Cape Cod

Since it was an older appliance I decided to replace the whole ice maker assembly. I carefully disassembled the old one and then installed the new one. piece of cake.

I replaced the run capacitor wich is located near the compressor, i first turned power off to fridge than remuved capacitor checked for continuity and the capacitor was the problem thanks

removed screws, pulled element out, and put new element in

unscrewed the 3 nuts, took off the electrical connection. Then put new one on. One problem, the ice maker had a hole on the side for the hose, mine needed one in the back. I used tape to hold it in place going over the part that was in the wrong place.

Disconncted power, pulled plug on disconnect, loosened 3 ice maker attach screws, removed ice maker. carefully removed old broken part, to understand reasembly. Reinstalled new water fill & bearing part.. hung icemaker and tightened attach screws. Reattached electrical plug.. turned on power, it all worked. .took about 45 min to remove, 15 min to reinstall. Right tools needed re disassembly AND ASSEMBLY

Had to remove the freezer door. Held on by 4 screws. Removed bottom screw on old icemaker and loosened the top 2. Slid the old icemaker up, removed the wiring harness and installed it on the new one. Took the wire out that turns the icemaker off and installed it on the new one. Hooked new icemaker on 2 screws, installed bottom screw and installed freezer door. Turned water back on and started making ice.

I performed basic troubleshooting to make sure there was power and water. Based on historical research on this particular ice maker, I decided that the best direction was to replace the entire assembly. I found this item on this site, ordered it and received it a few days later. I basically removed the ice pan and a few items in the freezer, removed the three mounting screws with either a flat blade screwdriver or nut driver, pulled the electrical harness out of the back wall of the freezer and transferred it to the new ice maker and then installed the new unit, really that simple. Iwas concerned at first, not seeing any activity in the new ice maker but after 15 minutes or so I heard ice falling into the ice bin. Well worth replacing seeing how simple this job was.

Model#MBF2255KEW (bottom Freezer) Turn fridge and freezer controls OFF. Move fridge out away from wall to give yourself working space and to clean later. Disconnect electrical plug from wall. Turn off water supply at wall or floor. Put down towel to catch excess water and disconnect water hose at water supply, lay it on towel. Move to the inside of freezer and remove freezer bins by pulling the door all the way out as far as it will go and then lifting by the handle up. locate the two hooks in the back and push forward to clear the bar and move to a safe location. Push the two rails all the way back into the freezer. Un plug wire harness from freezer by squeezing both side of the plug at same time and pull off. Remove the 3- 1/4" nut screws (2 at top and 1 at bottom ) from the ice maker and remove. Take the front cover, Wiring harness and wire bail from old ice maker and place it on the new ice maker. Install new ice maker and connect the wiring harness plug to the freezer connection. Hook up water line hose and tighten. Turn water on and check for leaks. Plug fridge into wall outlet and set refrigerator and freezer controls to 3 until refrigerator is cold and then set as needed. Give the ice maker from 3 to 6 hours to freeze and wait for that magical sound of ice being dumped into the bin. Throw away first batch of ice to make sure there are no impurities. Check for the delivery date of the new ice maker before you start and have coolers and ice for perishables. I removed the old one on the delivery date and cleaned the fridge and freezer inside out. I came to this page to get my repair plan and I hope this will help someone else.

When that one came and I went to install it, I found that my fridge was so old (almost 30 years) that the wire harness on the old icemaker could not be transferred to the new one. The old one was hand wired into the guts of the machine with wire nuts and other connectors. The new unit needs a plug in harness to match a plug connection on the ice maker. Also, the bent wire arm that senses ice bin levels was different, old unit hooked in with clips and such, new one pops into a socket in the new ice maker.

I called PartSelect back again, and the clerk spent a lot of time in the books (no parts in the online listings) and found new style connector and wire arm. Another 25 dollars and problem is solved.

Once those parts came, the actual installation was a breeze. Remove three screws, unplug the ice maker from the back wall of the fridge, plug new wire harness into new ice maker and the back wall of the frige, install new ice maker with the same three screws, pop the new style bent wire arm into place and pop the plastic cover from the old ice maker onto the front of the new one. Done! Took me ten minutes (plus two weeks of chasing parts, but only half an hour of actual time in those two weeks).

I let it make a couple of loads of ice that I disposed of (to capture any dust and crud that might have been on or in the new ice maker) and then turned it loose. We had a nice full bin of ice in the morning.