RB18FY-3AW (7B04A) Magic Chef Refrigerator - Instructions

I did not do the repair yet, there is no schematic on how to route the hose; also no description of how to do the routing/connections.

had to saw off the shaft to get the yoke off and tap the holes for the 8/32 screws. all holes should have been tapped by the factory. Other than these problems, everything else went pretty good.

I got the product very quickly. (thank you) Looked at online instructions that were quite vague. Pulled plug.Removed the holder for the fan motor slid it out to see what I had. Removed the mounting screws (3) and slid the motor an fan blade out. I made a cut between the wires and marked the "top" wire to motor to be sure to spin in right direction. Removing fan blade hold down clamp was NOT explained at all but I noted that the shaft on the motor was threaded, so I used pliars and held the shaft white un-screwing clamp. I cleaned the fan blades with degreaser and scraped edges of opening on holder opening. Make sure to use ALL the NEW parts included with this kit when re-installing. They send them for a reason. When slpicing and connecting wires it is a 50/50 shot if you don't mark before cutting. You can connect and try plugging fridge back for moment and make sure it is blowing OUT. Put everything back together and after turning DOWN the thermostats twice, fridge is back to usual. Ice maker is cranking out ice and outside case is cool to the touch.

Note: This can be a DIRTY job especially with 4 dogs in house. Fir and grease don't mix well

After trying to clean and use chemicles to remove residue, I found that it would not work. Ice would build up in tray causing an overflow in the fill process. this would freeze cubes in tray below causing dispenser not to work properly, New tray seemed to solve the problem. Removed old and installed new

Ordered the leveling bolts, very fast shipping, parts correct as shown. Purchased a condo by the shore, frige had no levelers, they went in smoothly & was done in no time.
Steve

Very slowly, had no clue what I was doing. Instructions were great, and even I got the job done.

First I removed all the screws from the back cover.
2nd removed fan nut and fan blade
3rd removed fan bracket
4th I traced wire to the condenser and disconnected wires from wire nuts.
Installed existing fan brackets to new motor kit
then reconnected wire nuts to new motor cord
Reinstalled fan nut and blade,
reinstalled cover, plugged it in and BAM .WORKS PERF!

Just took old ice tray out and put new one right in place in less than 30 seconds. I am very pleased with how fast the tray arrived after being ordered. if only everything ordered could be made this simple. You are a great company to deal with.

I pulled the drive ring off of the icemaker and replaced it with the new part. Saved a $150 service call plus cost of part. It cost me a little over $11.00 and a repairman probably would have charged $30.

I removed 7 screws hold the heavy cardboard cover on the rear of the fridge. The dificult part was taking the screws that hold the 3 fan motor braces on the fan out. After that it was a matter of making the wire conections and putting it back in. I did not have enough room to laydown to do the work, If i had it would have been a lot easier to see the screws that had to be removed. All in all an easy job, and the part was a perfect fit.

Removed 6 screws to get at broken part. Had to remember the disassembly sequence to properly reassemble. The whole process was relatively simple. I saved about $125 which would have been the cost of a repairman coming to the house.

removed old and instaslled new. biggest problem was getting to one of the screws.

Turn off refrig water supply, remove cardboard rear lower cover, disconnect two plastic lines (one for icemaker, the other for in-the-door water dispenser) and one copper fitting (supply line). Replace valve (mounted with one screw), reconnect, test for leaks.

The valve I was so sure was bad wasn't, replacing it didn't solve my problem. Turned out to be a frozen up icermaker water feed tube at the top rear of the refrig. The Fix: heat a metal rod of appropriate size in boiling water or with a hair dryer, poke it gently up into the water drop tube (sticks out just above the rear of the icemaker) from the inside and melt out the ice plug. Be sure to test this tube if you have the same problem, you should be able to disconnect the line on back of the refrig and blow air through the tube if it's clear. Saved the valve anyway for a spare.

Reattaching the kickplate clip was easy, but the tab that holds in place was broken. It would slide back when the kickplate was installed. I fashioned a replacement tab out of a piece of 3/32 aluminum bent into a U with the hammer. To hold it in place I drilled and tapped one hole and used a 6-32 machine screw.

Unplug fridge, unpluged fan motor from plug socket, removed bracket screws, removed fan retainer clip from shaft. removed screws holding fan to bracket