36551 (P1115402W) Litton Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Ivanka from Atlantra, GA
- Parts Used:
- 8009
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
burned oven bulb
The hardest part was taking out original light bulb because screws on shield where hard to unscrew after all this years . The old bulb vent out leaving neck in socket. It took narrow electrical pliers to get neck out .The generic appliance bulb did not fit and had aluminum neck ,not recommended for brass sockets in ovens.Putting new light bulb in was not the problem.
Was this instruction helpful to you?
Thank you for voting!
Did not work light does not come on when the door opens. Would try the light socket. It not sure how good the switch got plugged in.
By watching a video.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dale from Fenelton, PA
- Parts Used:
- R0131577
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Wrench (Adjustable)
Not Getting Cold Enough
Removed and Replaced
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Don from Granbury, TX
- Parts Used:
- R0181181
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Main door was making a thunping noise when opened.
Took the door off, and replaced the plastic shim on the bottom that was the cause of the problem. The shim had broken into pieces and was no longer holding the door in height and alignment. I was proud of myself that I could repair it myself and avoid a $125.00 service call from a repairman. Total cost of repair including shipping and handling was just south of $12.00.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Wasilla, AK
- Parts Used:
- R0131577
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Wrench set
Defrost timer had quit working
The repair was relatively simple.
The hard part was diagnosing the problem. Two of the sheet metal screws were hard to get at.
The online support helped in isolating and fixing the problem. The frig works fine again.
The hard part was diagnosing the problem. Two of the sheet metal screws were hard to get at.
The online support helped in isolating and fixing the problem. The frig works fine again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cecelia from Beaver Dam, WI
- Parts Used:
- W11384469
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
light staying on
A very cold and brittle switch in a 17 year old fridge. Used screwdrivers to pry out with some resistance Had to cut the molded plug in half and split wires, because replacement contacts were farther apart than the original. End result, works great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donald from Mundelein, IL
- Parts Used:
- R0181181
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The door clicked when opened or closed.
I followed the other web notes with one change .Since I too forgot the lube , I used a pry bar and block of wood to lift the door and a tooth pick to glob some lube in the lower hinge.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- kent from fishers, IN
- Parts Used:
- R0181181
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Refrigerator door side lower closer cam broke
The worst part was unloading the door shelves. Removed upper hinge cover and hinge hex screws. This allows the door to be removed. Lay the door on side. Remove screw that holds cam in place. Replace
broken cam with new piece. Put the door back on the hinge pin and replace upper hinge screws and cover.
Now reload all of the stuff.
broken cam with new piece. Put the door back on the hinge pin and replace upper hinge screws and cover.
Now reload all of the stuff.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Fonce from Ft Lauderdale, FL
- Parts Used:
- R0181181
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
lower cam broke
Remove the grandkids pictures from the door then empty the contents inside the door. Remove the top hinge cover and the top hinge bracket. Lift the door off the bottom pivot. Replace the lower cam by removing one screw. With the door in the horizontal position, remove and replace the upper cam. Apply a little grease on both cam surfaces. Align the door before tightening the top bracket and your done. If you did not take a picture of the door before you started the project you will have to rely on memory to arrange the pictures in the proper location.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Shirley from Las Vegas, NV
- Parts Used:
- 8009
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Light burned out in upper oven
Screwed in light bulb and glass protector
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- peggy ann from forest city, NC
- Parts Used:
- 8009
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
replaced oven lightbulb
very easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jim from Milford, MI
- Parts Used:
- R0181181
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench set
Plastic Cams on frig door cracked in halk/door wouldn't close easily
Removed the top hinge (4 screws)-lifted the door off of the lower hinge-replaced both halves of the cam kit and mounted the door and reattached the upper hinge.
Probably took about fifteen minutes total.
Probably took about fifteen minutes total.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George from North Scituate, RI
- Parts Used:
- W11384469
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Broken light switch
Part was easy to order, delivered quickly, installation very easy. Just unplug the unit, pop out the old swich using a screwdriver, disconnect and reconnect leads and pop switch back in. Definitely recommend that you can do it too.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from Hinsdale, IL
- Parts Used:
- W11384469
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Door Light switch cracked Mounting
I noticed that the refrigerator was having trouble maintaining temperature. Thought it might be time for new one until I found out that a new frig was $5k to $7K. Just happened to notice that the light switch didn't look quite right (was not sitting sqaure to the door). Once I pressed it it came loose. I then realized the the lights were staying on (50 watts of heating). Replaced the switch and the frig started working like new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Schwenksville, PA
- Parts Used:
- 8009
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
oven light burnt out
1. Unscrewed glass cover on bulb
2. Removed old bulb
3. Screwed in new bulb
4. Replaced glass cover
5. Mixed drink & baked cupcakes
2. Removed old bulb
3. Screwed in new bulb
4. Replaced glass cover
5. Mixed drink & baked cupcakes
Was this instruction helpful to you?
Thank you for voting!