36558 (P1115404W) Litton Refrigerator - Instructions

I replaced the run capacitor wich is located near the compressor, i first turned power off to fridge than remuved capacitor checked for continuity and the capacitor was the problem thanks

First I pulled the fridge out from the wall and turned off the water supply. Next I removed the access panel on the bottom front of the fridge. Located behind the panel was the water supply line for the water dispenser in the door which has a disconnect the I simply unscrewed so that I would be able to lift the door off of the bottom hinge. Next I took one screw out of the top hinge cover to access three small bolts and disconnect the electrical connections to the door. After removing the bolts I lifted the door off and took out the small screw holding in the bottom cam and replaced with the new one. After reinstalling door I removed all the small bolts holding on the freezer gasket. After this the gasket easily pulls out and began installing the new gasket. This part of the job was the most time consuming. After I had the gasket back behind the pinch rail I began reinstalling the bolts. Since the gasket was bent during shipping I simply took a hair dryer to the slightly bent parts of the gasket to get them to lay flat. Freezer now has a great seal and stays closed when refrigerator door is being shut.

removed old and instaslled new. biggest problem was getting to one of the screws.

Pried out old part with screwdriver. Unplugged. When new part came, just plugged it in and pushed the part into place.

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires... Put a thermometer in a glass of water & now runs at 38 degrees.

I removed 7 screws hold the heavy cardboard cover on the rear of the fridge. The dificult part was taking the screws that hold the 3 fan motor braces on the fan out. After that it was a matter of making the wire conections and putting it back in. I did not have enough room to laydown to do the work, If i had it would have been a lot easier to see the screws that had to be removed. All in all an easy job, and the part was a perfect fit.

I just popped out the old switch with a flat head screwdriver. Removed the connections and then installed new switch by reversing steps. Popped in back in and the light went on.

Talked to a bud who does this kind of work and he walked me thru the simple job. Also watched a you tube segment. Very easy job. Took off the front kick vent panel. Unscrewed the metal holder and unplugged old part, plugged new part in and put panel back on. Turned on unit and it is working like a charm. Got my fingers crossed just in case.

Unplug fridge, unpluged fan motor from plug socket, removed bracket screws, removed fan retainer clip from shaft. removed screws holding fan to bracket

The instruction sheet supplied with the new motor described the steps to take very good. Replaced the rubber grommets for the three motor mounts also. A flashlight or light source was needed or was very helpful.

Pull refrigerator out to access back, unplug unit and remove the 3 .25" screws cut the power leads to motor and install new with easy to understand instructions provided with new motor. Plug refrigerator back in and enjoy your cold beverages once more. EASIEST REPAIR EVER.

bulbs were not burnt out. received the new switch in a few days. watch the short video, was good to see how it comes out. used a putty knife to release the defective switch, removed wires put them on the new one and posed the new switch back in. Not bad Part cost $11.00 7 dollars shipping so for 17 bucks it works great. nice to see what is inside the refer!

We looked up the problem online with the model number of the refrigerator. We ordered the part and followed the video installation that was sent with the order and was found online prior to purchasing

The fridge door was easy. Just unscrew top and lift off hindge. The freezer door took longer. But I had the user guide which helped. We unhooked the power harness at the top of the door, and disconnected the water line at the bottom of the door.

Frankly, it wasn't that hard for me because I had my son-in-law do it!

Partition between Freezer and Fridge was running very hot. (Warm is normal). Oiling fan did not work. The only problems encountered in the replacement were getting fan out and in through coolant lines, cut plug off to accomodate generic fan wiring, getting the screws back in without cooking your hand on a hot compressor. Unit works great!