36591 (P1108403W) Litton Refrigerator - Instructions

Removed top hinge cover and socketed out hinge nuts. Lifted door off bottom hinge. Socketed out broken bottom cam and replaced with new. Reset door with someone lifting and the other guiding. Reattached top hinge and cover. Voila.

removed door.examined problem,. installed part. super easy

Unplug wire harness back of fridge. Unscrewed 4 screws on guide for ice bin. then unscrewed two screws holding ice maker to wall of fridge. removed ice maker. then had to take front cover off (pull hard, it comes off) and remove wire harness plug from the ice maker. save this, front cover, and all hardware to re-use. reverse steps to reinstall, including wire guide that goes up and down to stop and start ice maker when bin fills. Have to put this into front part of ice maker correctly for it to work. make sure it is down so that it will produce ice. ice tray took a few hours to fill with water initially, must be on a timer or something.

As per instructions. Removed parts from old ice maker, and installed them on new one, Then installed it in the freezer. Works good.

I did not do the repair yet, there is no schematic on how to route the hose; also no description of how to do the routing/connections.

Old ice maker leaking water and produced ice cubes with black inclusions. First, I removed old ice maker per video instructions. Transferred electrical cable, cover, and bail to new ice maker. First installation failed because I failed to make sure water tube correctly enter back of ice maker. No ice. Initially thought electrical cable wasn't firmly in place. Then I noticed frozen water dripping down back of freezer. A clue! Removed ice maker and reinstalled making sure water tube went through the hole in back of ice maker. Now the new ice maker works beautifully!

very easy. removed the old solenoid because it was cracked and spraying water all over the floor. installed the new part, turned on water supply and that was it!! water dispenser in the door works better, it fills a glass faster and the ice maker works better too.

Removed Ice carrier and diassembled the Ice carrier with a socket set. Four screws, cap came right off. Placed the new one on and finished.

Merely remove the front bottom screw that attached the ice maker to the refrigerator
Lift the ice maker gently off of the 2 top screws
Unplug the icemaker wiring harness from the back of the refrigerator, and remove
Snap off the end of the maker and remove the keeper for the wire arm
Remove the wire arm and install on new maker
Unplug the wiring harness from the old maker and plug into the new one
Plug the harness into the refrigerator, slip the new maker over the top screws, with the water feed tube inserted into the maker
Install bottom screw into the bracket that holds it in place.
This took less than 5 minutes.

I took out 1 screw , unplugged the icemaker and lifted it out and installed the new one and had ice in no time at all. can't get much easier.

Removed the top hinge cover with Philips screwdriver. Removed the three bolts holding the top hinge in place. Removed the top hinge, and lifted the door off the remains of the lower hinge. Unbolted the remnants of the lower hinge closure mechanism and replaced it with the new set. Reassembled the door on the lower hinge, and then replaced and bolted back on the top hinge. Door back to full working order in less than fifteen minutes.

Followed the online PartSelect video instructions and it was very helpful. The ice maker has to cycle through before it starts making ice so don't be alarmed when nothing happens when you first hook it up.

On PartSelect.com this part is only associated with the icemaker. It is actually a dual valve... one for the ice maker and one for the water dispenser. Be sure to match the blue and brown colors of the valve housings to the same hose colors.

The really scary part of this job was cleaning up behind and under the fridge, but also something that was long over due and the perfect opportunity to vacuum out the condenser coils.

Removed 7 hex screws holding carboard cover in place, verified water valve was inop. Ordered and recieved new part and installed. Diagnostic and actual repair under 1/2 hour.

I got the product very quickly. (thank you) Looked at online instructions that were quite vague. Pulled plug.Removed the holder for the fan motor slid it out to see what I had. Removed the mounting screws (3) and slid the motor an fan blade out. I made a cut between the wires and marked the "top" wire to motor to be sure to spin in right direction. Removing fan blade hold down clamp was NOT explained at all but I noted that the shaft on the motor was threaded, so I used pliars and held the shaft white un-screwing clamp. I cleaned the fan blades with degreaser and scraped edges of opening on holder opening. Make sure to use ALL the NEW parts included with this kit when re-installing. They send them for a reason. When slpicing and connecting wires it is a 50/50 shot if you don't mark before cutting. You can connect and try plugging fridge back for moment and make sure it is blowing OUT. Put everything back together and after turning DOWN the thermostats twice, fridge is back to usual. Ice maker is cranking out ice and outside case is cool to the touch.

Note: This can be a DIRTY job especially with 4 dogs in house. Fir and grease don't mix well