78344 LG Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- David from PENNSVILLE, NJ
- Parts Used:
- 6600JB1010A
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Switch stops working
Replace with new switch. this is the third switch i have replaced in 10 years. the only part, besides a light bulb, that has gone bad. obviously this is a problem with this model for Kenmore, or just poor switch design.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jane from SHORELINE, WA
- Parts Used:
- 6600JB1010A
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Door switch would not turn on interior refrigerator light.
I had previously watched a YouTube video (do this first!!) on a similar Kenmore model so I knew what to look out for: (1) turned off power, (2) took thin putty knife to slip under outer lip of switch (most screwdrivers are too thick), (3) wiggled switch at front end to release the tab, (4) unplugged from the socket, (5) plugged in new switch, (6) popped new switch back into door, (7) turned on power. Voila !! Super easy. I couldn't believe it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Philip from Ashland, MA
- Parts Used:
- 6600JB1010A
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Lights didn't come on when door was opened
I have moderate to good mechanical skills, but getting the old switch out was a sizeable challenge. Since this switch suffered some damage during extraction, I was lucky to have ordered a new one to replace it. Reinstall took approximately 90 seconds. PartSelect saved me an expensive service call.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Harley from IOWA FALLS, IA
- Parts Used:
- 4930JJ2028A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Top of retainer broke
Followed instructions
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Karyn from DURHAM, NH
- Parts Used:
- 6600JB1010A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Replace the light switch for the refrigerator
Cover the putty knife with tape so you do not scratch the side wall where the switch is located. Slide the knife under the edge of the switch and push in a bit towards the switch and slightly twist to pop the switch out of its hole. Disconnect the wires from the switch and simply plug in the new switch. Push wiring back into the hole and careful push the switch into the hole until it snaps into place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Ashland, KY
- Parts Used:
- 6615JB2005C
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Refrigerator not cooling
Used a screwdriver to remove covers. Used a blow dryer to defrost coil in freezer. Cut zip tie and removed old controller assembly. Inserted new controller assembly and secured with zip tie. It took 24 hours for the fridge to cool completely. Now it works fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alma from Winterport, ME
- Parts Used:
- 6600JB1010A
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
the light did not work when door was opened. At first it would flicker then off completely.
My son just pried out the old switch with a screw driver snapped out the old one and snapped in the new one. Pretty sure even I could have done this. Very quick and easy. Thanks. :-)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from STREATOR, IL
- Parts Used:
- MJB63029901, 4430JJ2005B
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Door stopper broke
Very simple, remove broken part with screwdriver and replace with new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tammy from HAGERSTOWN, MD
- Parts Used:
- 6600JB1010A
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Refrigerator light had a short in it and would randomly work
Unplugged the fridge. Used a screwdriver to loosen the switch. Easy to disconnect from fridge and just plugged the new switch in. Popped right back into the side of the fridge and worked perfectly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nancy from Hallandale Beach, FL
- Parts Used:
- 6600JB3007A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
light was not going on sometimes, or needed wiggling to work
purchased a new switch. The old switch just needed to be lightly pried out with a screw driver, then it was simple to unplug the old, and plug in the new. Voila! Light !
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Vacaville, CA
- Parts Used:
- MJB63029901
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
refridge door stopper broken
easy, a screw driver repaired in a mintue
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jack from Ellenton, FL
- Parts Used:
- 6600JB1010A
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
light out
slid screw driver under edge of switch, easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dean from Intervale, NH
- Parts Used:
- 4930JJ2028A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Door latch (cam) at door top broke off from the gasket holder. Gasket was fine so only needed new holder.
Gasket held in place by plastic bezel. Remove bezel by carefully pulling it toward you. Held in place by plastic clips. May need to pry carefully near clips. Pull gasket away from front edge of door. Gasket holder held by plastic swivel pieces top and bottom. Snap these out. Slide the gasket holder off the gasket. Remove the screws and slip the metal rod out of the broken holder. Retain screws, plastic clips, and cam. Slide the rod into new holder adding plastic clips and cam. Replace screws. Slide holder back onto gasket. Snap plastic clips into slots, being careful to bend the springs back so they go into the channel. Replace bezel. See videos on replacing door gaskets.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Janet from West Hempstead, NY
- Parts Used:
- 4975JJ2028D
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
sliding rail
I removed the broken rail & installed the new rail with a screw driver. The screws were located in somewhat difficult position. The rail works OK but has a tendency to stick & the tray holder sometimes slips out of the new rail.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Bay Shore, NY
- Parts Used:
- EAG62831801
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Interior Light Would Not Turn Off
Tape off the light button so door alarm does not go off. Take off the clear light shield and remove the light bulbs. Be careful, bulbs may still be HOT!! With Phillips head screw driver unscrew the light plate assy. Drop it down in a comfortable position. Disconnect the connector, unscrew the thermal sensor and remove light assy. Install new light assy into light plate assy. There is no thermal senor in the new assy. Snap light plate assy back into place and install the two screws previously taken out. Install bulbs and clear cover. Remove tape from light door switches and you are done. Lights should go on and off when door buttons are pushed in and out.
Was this instruction helpful to you?
Thank you for voting!