LMXS27676D LG Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Paul from CLEARFIELD, UT
- Parts Used:
- AEQ73110210
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Ice Maker Can’t Rotate/Discharge Ice
First, remove power to the refrigerator.
To replace the ice maker you first have to remove the back mounting assembly, which ice maker is attached to.
Only three Phillips head screws need to be removed: 2 on the bottom and 1 on the back of the ice maker mounting assembly. Do not remove the two diagonal Phillips head screws holding the dispenser motor on the reverse side of the mounting assembly.
As you pull out the mounting assembly to the front you will see a connector on the top inside, which must be unplugged. A narrow standard screw driver will help the connector lock to release; slide the screwdriver tip under the connector lock clip and it will allow the connector to be unplugged.
Once the ice maker mounting assembly is removed and placed on a flat surface it will be self evident as to how to remove and replace the ice maker. The 1” tape might be needed during the cable re-routing process. However you can reuse the original tape required to be removed during the ice maker remove and replace process, if possible.
Reinstall the ice maker mounting assembly in the reverse order it was removed.
Apply power to the refrigerator.
Cycle the ice maker to Off and then back to On. It may take an hour or two before the ice maker produces ice because the temperature inside the ice maker must reach “0” degrees Fahrenheit before it will begin making ice.
Pull the ice maker
To replace the ice maker you first have to remove the back mounting assembly, which ice maker is attached to.
Only three Phillips head screws need to be removed: 2 on the bottom and 1 on the back of the ice maker mounting assembly. Do not remove the two diagonal Phillips head screws holding the dispenser motor on the reverse side of the mounting assembly.
As you pull out the mounting assembly to the front you will see a connector on the top inside, which must be unplugged. A narrow standard screw driver will help the connector lock to release; slide the screwdriver tip under the connector lock clip and it will allow the connector to be unplugged.
Once the ice maker mounting assembly is removed and placed on a flat surface it will be self evident as to how to remove and replace the ice maker. The 1” tape might be needed during the cable re-routing process. However you can reuse the original tape required to be removed during the ice maker remove and replace process, if possible.
Reinstall the ice maker mounting assembly in the reverse order it was removed.
Apply power to the refrigerator.
Cycle the ice maker to Off and then back to On. It may take an hour or two before the ice maker produces ice because the temperature inside the ice maker must reach “0” degrees Fahrenheit before it will begin making ice.
Pull the ice maker
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jodi from WINTER GARDEN, FL
- Parts Used:
- AEQ73110210
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
My ice maker wouldn't release the ice, nothing was frozen and the motor would just bind
I bought the ice assembly motor only, super easy to install, remove the three main screws, lift out assembly, detach the cable. Then remove the screws on the parts, lift the tape, redo everything in reverse and it works flawlessly!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Larry from GODDARD, KS
- Parts Used:
- AEQ73110210
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
The refrigerator ice maker needed replacing
The only tool required was a Phillips screwdriver. I disassembled the old icemaker and unplugged the electrical snap in device. I removed the ground wire. Then reversed the steps in replacing the refrigerator ice maker kit assembly. It took slightly over 30 minutes to remove and replace the ice maker.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Johnny from MOUNT OLIVE, AL
- Parts Used:
- AJU72992601
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Leaking
Swapped old one with new one. New one had extra plug not needed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Katharine from FAIRFIELD, OH
- Parts Used:
- AJP73574805, AGF80300702
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
tray was a tight fit but we got it in
work with the tray gently. To ensure this did not break.
Water filter installed was installed exactly the way the instructions stated to be
Water filter installed was installed exactly the way the instructions stated to be
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from ELLWOOD CITY, PA
- Parts Used:
- MHY62044106
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
The original spring in the mullion door broke
I disconnected the refrigerator power, removed the 2 screws holding the mullion door on the left side of the refrigerator French-door (it’s the flap that allows the door to close). Removed the broken spring and installed the replacement spring in its place. Reinstalled the mullion door by putting it in place and installing the previously removed screws.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eugene from ENCINITAS, CA
- Parts Used:
- AEQ73110210
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Ice tray cracked
Removed the old one and replaced with new just remember do your do diligence watch YouTube videos makes repair a lot easier
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Angela from SAINT JOSEPH, MO
- Parts Used:
- AEQ73110210
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Ice tray was not rotating any longer
Took the old one out and put the new one in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Susan from SAFETY HARBOR, FL
- Parts Used:
- MHL62691504
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Previous glass shelf shattered into a million pieces while cleaning.
Just laid the shelf down. Fit like a glove!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from HAMPTON, GA
- Parts Used:
- MHL62691504
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The glass shattered & needed to be replaced
Just popped it in, just as easy as that!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- RODNEY from GERMANTOWN, TN
- Parts Used:
- AGU74110903
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Spring broken on front plate
Unscrew two Phillip screws on center hing , push frt plate down and replace.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Katherine from NEW PRT RCHY, FL
- Parts Used:
- MHL62691504
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- More than 2 hours
Broken shelf for the vegatable bins
The glass was ordered correctly. The part was too big for mt refrigerator. I tried to send it back, but I got no reply. I tried cutting the glass to size and it shattered. I wasted 60.00 and im disgusted with your company.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donald from BETHPAGE, NY
- Parts Used:
- AJU72992601
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Ice Maker and Water dispenser stopped working
Pulled the fridge out.
Unscrewed the back cover and the one screw holding the value assemble.
undid the 2 hoses and replaced the part.
Super SImple/
Unscrewed the back cover and the one screw holding the value assemble.
undid the 2 hoses and replaced the part.
Super SImple/
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from YORKTOWN, VA
- Parts Used:
- AJU72992601
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Lower ice maker water feed froze and caused leak. Needed new water valve.
Took pics of original install, removed old valve, water tubes & plugs. Installed new valve, reconnected electronic plugs, water tubes, turned water back on and all has been well since. Thank you for your timely delivery!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ken from GREAT FALLS, MT
- Parts Used:
- MHL62691504
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
need new shelf
Opened box, unpacked shelf, placed in refrigerator. It took longer to open box than it did to install. Very easy!
Was this instruction helpful to you?
Thank you for voting!