GR-B25AUSA LG Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Scott from JUPITER, FL
- Parts Used:
- 6615JB2005H
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers
Replace Thermistor in back of freezer
Turn off power, remove upper and lower drawers (may need to open upper refrigerator doors to remove large freezer bin,) remove drawer supports (upper and lower), remove rear freezer panel (trick is to loosen 4 screws on fan bumpout to get the panel to come free from the freezer side wall), test thermistor with multimeter (should have continuity or near zero resistance across 2 orange fuse wires) before cutting zip ties, cut zip ties holding Thermistor in place, remove old Thermistor, install new Thermistor, install new zip ties, replace rear freezer panel, install upper and lower drawer supports, install drawers, turn on power, should be fixed if error code doesn't return after 6 hours.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rick from CLEVELAND, TN
- Parts Used:
- 5901JA1021A, 4681JB1027C
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Very bad noise which stopped when the door was opened
The Refrigerator now runs very quite.
After watching several videos I started on mine and found that it was a bit different than any in the videos. However all but the back panel was shown and that was helpful.
The back panel was a bit difficult but a hair dryer seemed to help .
All in all it was a good choice to do it myself as it was done quicker than waiting on a repair man.
After watching several videos I started on mine and found that it was a bit different than any in the videos. However all but the back panel was shown and that was helpful.
The back panel was a bit difficult but a hair dryer seemed to help .
All in all it was a good choice to do it myself as it was done quicker than waiting on a repair man.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Billy from AUGUSTA, GA
- Parts Used:
- 4987JJ2002S
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Seal was damaged
Have your wonderful Grandson do the repair work.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marissa from BOYNTON BEACH, FL
- Parts Used:
- 3550JA1388B
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
my cover lamp broke
I just popped in the new cover lamp. It took less than 5 mins. if that much.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Claude from SAN DIEGO, CA
- Parts Used:
- 4931JJ2002F
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Broken door gasket retainer
Go to this site on You Tube to watch the "how to" replace the gasket retainer. The retainer I needed did not come with brackets or the cam you will need. You will need transfer them from the old retainer to the new one. Not hard, just be mindful of position of the items you remove to put them back in place the same way. A metal rod holds the brackets and spring in place with a screw on one end to prevent rod from sliding off retainer. The cam has a screw that holds it in place, use from old retainer. If the old cam is not broken use the one from the old retainer. It is not hard and you will save $$$ that you would pay an appliance repair company.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George from WHITE BIRD, ID
- Parts Used:
- 4681JB1027C
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Blower motor out on condenser
followed detailed movie from Utube video
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- marvin from montgomery, TX
- Parts Used:
- 5220JB2010A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
icemaker quit
i first replaced valve as the water line hung up and broke the valve as i was moving fridge out,be careful about doing this,now i need to replace icemaker as its not working,ps it wasnt the water valve ,i broke it,so first replaced it now icemaker ,lg stinks for the 2 yrs icemaker has worked,my previous kenmore icemaker thru door worked for 23 yrs and was working the day i replaced it, the new electronic appliances are nice when they work!!!>Marvin
Was this instruction helpful to you?
Thank you for voting!