LFX31925SW (02) LG Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Thomas from CHULA VISTA, CA
- Parts Used:
- ADX72930460
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Left side gasket was torn and would seal properly
Took off the French door Mullen by unscrewing middle area. Unconnected the wires for the door sensor. Then detached old gasket and replaced with new gasket. Reattached the wiring and snapped Mullen flap in place and finally rescrewed to the door. Seal is very good now.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bob from Phoenix, AZ
- Parts Used:
- AEQ73110205
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Ice would not fall
Replaced Ice maker unit
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from NAPERVILLE, IL
- Parts Used:
- AEC73317702
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Roller on rail broke off
easy repair. First step is you need to remove all food from bottom shelf and remove all three produce drawers. Then remove the meat drawer. You will need to lift the bottom self off the rail to remove. It is not heavy and does not need to be fully taken out of fridge - easier if you do but some what hard to get out.Unscrew the rail and unplug the old rail. Clean off the fridge - my fridge was gross behind the rail. Insert the rail into the fridge and then screw in the two screws. Place the bottom self back on the two rails and you are done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bryan from ADA, MI
- Parts Used:
- AEQ73110205
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Ice maker not making ice, ice tray overfills and cannot dump, ice sticks together and will not dispense
This repair is pretty straight forward. Just remove the 3 screws that hold the ice maker and bin assembly in, unplug the wire harness connector, then remove it from the refrigerator door. Once removed you simply need to remove 3 more screws that hold the ice maker to the auger/bin frame, remove the temp sensor, and a couple pieces of tape. Re-assemble the new ice maker in reverse order and you are all set. I think part of the issue I was having was due to mineral buildup in the tray as well so it had a hard time cracking and removing the ice. Not sure why it was overfilling, maybe the sensor was broken or had buildup on it as well. This solved all the problems I was seeing and now it makes great ice that doesn't stick together and form a bridge in the bin.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from BOWDOINHAM, ME
- Parts Used:
- ADQ36011715, AGF80300702
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers, Socket set
The hose that feeds the Ice Maker broke,right where it goes in the Fridge.
I actually didn't use what I got. Because there was all kinds of tubing coiled up in the door. We just fed the exsess all the way through the Fridge,and Bingo! It was done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Craig from SPRING HILL, FL
- Parts Used:
- MDS38201426
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Ice crystals appearing on the face of the freezer draws
Part Select had a great video which made the repair easy, using a putty knife to start removing the freeze door gasket. Once removed the install is simple just snap the new gasket into the track, but start at the corner. Other company's have a video requiring you to remove the entire freezer compartment out of the appliance, unnecessary waste of time and labor.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Scott from KENT, WA
- Parts Used:
- AAP73252202
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The shelf on our refrigerator was cracked so I ordered a replacement.
Some have said that the installation took 5 minutes. Mine took less than that, and I did it with one hand. I had a beer in my other hand.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William L from SUMAS, WA
- Parts Used:
- 6600JB1010A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
light didn't come on when the door was opened
I took a very thin bladed screwdriver and took the old part out -carefully.
The new part fit in quite easily.
The new part fit in quite easily.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from PENNSVILLE, NJ
- Parts Used:
- 6600JB1010A
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Switch stops working
Replace with new switch. this is the third switch i have replaced in 10 years. the only part, besides a light bulb, that has gone bad. obviously this is a problem with this model for Kenmore, or just poor switch design.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Maryann from BROOKFIELD, IL
- Parts Used:
- MDS38201426
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Icing up in the freezer due to poor gasket
Watched a couple of YouTube videos and then went at it
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Theodore from SACRAMENTO, CA
- Parts Used:
- AAP73252202
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Broken Door Basket
Un-wrapped the basket......Installed with NO tools......
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barbara from HAMILTON, NJ
- Parts Used:
- MHL42613220
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Glass shelf broke during cleaning
Very easy. Just slipped it back into place
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- shirley from ONALASKA, WI
- Parts Used:
- 6600JB1010A
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Light switch for refrigerator not functioning
Followed instructions online
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from JACKSONVILLE, FL
- Parts Used:
- ABQ72940005
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
The overlay control Panay was broken at the bottom
We pryed the ice dispenser housing out unscrewed the overlay from the relay board and then reversed the process to put it back in time consuming but went slow as not to brake tabs or crack housing
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donna from BILLERICA, MA
- Parts Used:
- AEC73317702, AAP73252202
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Broken wheel on rail for deli Drawer
Need to remove the deli drawer and shelf above. I took out the glass first to make shelf easier to handle. Unscrew old rail and put new one on. Took more time to empty items on shelf. My 17 year old son made the repair.
Was this instruction helpful to you?
Thank you for voting!