LFXS24566S (00) LG Refrigerator - Instructions

This was an incredibly easy repair! 1 phillips screwdriver and two screws. Disconnect the small adapter, and you are good to go!

Removed two screws from door and three locking brackets with a small common screw driver. Raised the bracket, slide in the spring, held down the bracket, installed screws and plastic covers. Less than 2 minutes. Easy application no problem with the new spring or ,mullion..

Found the part on Parts Select. Ordered the part, which came quickly. While waiting for delivery. I watched a short video on how to replace this part. I'm a 73 yr. old female, and no trouble at all. I really felt a sense of accomplishment. Thank you Parts Select.

Expensive to have repair man come out and find out that I’ve been mailed wrong spring again. My icemaker is on the left hand side this is the side of refrigerator- I need the spring for left side with the ice maker. Twice they have mailed me the Wrong spring that goes on the right hand side I have tried to explain this to the person that waits on me. Do I have to pay for another spring and mail this one back ?i have mailed one back and postage is getting expensive.

Replaced with new mullion

The spring broke on the flapper (mullion) on my refrigerator. I sent a chat message to PartsSelect (they answered right away) to see if they had a replacement spring but it was not available so had to order the whole mullion. They gave me the part # I would have to order. It arrived quickly. The new mullion didn’t have a visible spring but it worked the same if not better. I just had to remove 2 screws on the center plate on the existing mullion, pull the plate out enough so you will be able to slide the mullion (the wires are under the plate kind of like the ones you see on a ceiling smoke detector) but you can’t get under the plate until you release the mullion. Push up on the mullion so that the plastic tabs on the top and bottom are released. Once the mullion is released (you have to hold it), you’ll see the wires. Unhook the wire part by just pushing down on the little tab and remove it. To install the new one, just reverse the steps. Align the top and bottom plastic tabs to fit into the slots, just enough to hold it in place. If the plastic tabs are not already flipped out, you’ll have to just flip them out. The top tab does not have tension but the bottom tab has tension so just push on it with your finger to flip it out. The plate covering the electrical is a rather tight fit and you have to make sure the little tab on the inside of the plate is above and behind the tab on the inside where the wires are so it slides behind it so you can get it in position before sliding the mullion back down into place and the electrical plate is in place too. Then screw the 2 screws back in. The hardest part is holding the mullion while un-attaching the electrical and just make sure you stuff the wires in enough so you can get the plate back in position. I’m a 75 yr old woman and managed fine by myself. At first when installing the new one, I couldn’t slide the mullion down enough to get the electrical plate in position and then realized I had to have the little tab inside the electrical plate behind the tab inside the wire compartment so they didn’t hit one another when pushing the mullion back down. Then, all went fine.

Remove 2 screws holding to door. Slide assembly up. Unplug connector. Remove old Plate Assembly. Do reverse to reinstall. Plug connector. Push in wires. Slide plate on. Fasten screws. Done

Removed mullion strip with Phillips screwdriver replaced spring reinstalled the mullion strip all in about 15 minutes.

Remove 2 screws swing light down a little bit and pull it to front unplug wires . The hard part of job was finding new replacement light, Partselect.com was only sight I could find that had new replacement number and had the light . Other sites including LG site would only tell me the part number on old lights was discontinued 2 of sites said try used appliance dealers

I bought the ice assembly motor only, super easy to install, remove the three main screws, lift out assembly, detach the cable. Then remove the screws on the parts, lift the tape, redo everything in reverse and it works flawlessly!

The only tool required was a Phillips screwdriver. I disassembled the old icemaker and unplugged the electrical snap in device. I removed the ground wire. Then reversed the steps in replacing the refrigerator ice maker kit assembly. It took slightly over 30 minutes to remove and replace the ice maker.

Swapped old one with new one. New one had extra plug not needed.

Watched the video. Took the screws out, unplugged the connection and slid mullion off. Then plugged the new one in, slid it on and attached the two screws.

Removed ice bin
Unscrew the 3 screws.
Lift ice maker for the bottom to remove it but do not pull it until the power is unplug from the part.
Install the new part the same way you removed the old part.
Turn the switch and waiting 48 hours before the ice bin start getting ice

Scary not hard. But pry panel out start at bottom or right side and pull. and was told from tube video that lg said if you break a few tabs that was normal and not to worry there is plenty. I think I broke one but after repair just pushed it back into place and it is good as new. The broken part was obvious and easy to replace. Just go for it