LSC27921SB02 LG Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- David from Lewisville, TX
- Parts Used:
- AAP34518101
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Manufacturer Cahnged Part Desin
Not the fault of partselect. The manufacturer had decided to modify my part and still specifying that it was the NEW part number and that it was the direct replacement (shame on LG). Well its not the same part. The partselect CSR worked with me to try and find the previous design to no avail, even going so far as to give me the phone number of an obsolete parts seller... wow! Without a whimper parts select credited my account for the part that would not fit!! Without a doubt I will use them again. Way to stand behind your sale!! And also I got the parts within two days, amazing. The ones that did fit were well packed in perfect condition and on time. DON'T HESITATE TO USE THIS COMPANY
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rich from Pequannock, NJ
- Parts Used:
- 6600JB3007E
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
interior lights stay on
Changed door switch. Repair worked for a few days but re-occured. Possibly the other switch is bad .
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Nolensville, TN
- Parts Used:
- 3390JA1150A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Ice tray was bent and spilling water onto ice making it freeze
I took the ice out with one screw and took out the old tray the new one slipped right in and I hooked up the little heat strip with one snap works perfect cost $10 I was told by appliance repair tech that I needed to replace the ice maker for $450 saved $440 dollars replacing the bent or warped ice tray
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Eagle, WI
- Parts Used:
- 5989JA1002D, 3550JA3095A, 3390JA1150A
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Ice cubes did not drop out of tray when the ice maker cycled
1) Take out 3 screws from top of icemaker. 2) Unplug electrical connector from wiring harness. 3) Remove icemaker unit from freezer and then remove frozen cube sensor with clip and rear insulation. 4) With your hands pull cube tray motor out of the holding clips with the tray- if this is too difficult, spread bracket and only remove the tray from the unit. 5) Insert new tray into slots and install new or existing ice sensor, insulation, and sensor clip. 6) Reinstall icemaker unit to ceiling of freezer, don't forget to plug into wiring harness. 7) Turn unit on and make some ice!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nicholas from Melborne, FL
- Parts Used:
- 5221JA2006D
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Wrench set
Threads were striped on water valve leaked needed new one
Shut water valve off drained water in refrigerator instAlled new valve
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- steve from clarence center, NY
- Parts Used:
- 5989JA1005D
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
My ice maker overflowed water and made a mess in the freezer
The part was extremely easy to replace. The unit came out with one screw, and I had to unplug the wire connection. After removing I noticed the ice tray was cracked - that's what caused the problem. The new unit went in easily with 1 plug in connection and 1 screw. I was done in less than 10 minutes.
Was this instruction helpful to you?
Thank you for voting!