LFX31945ST (ASTCNA0) LG Refrigerator - Instructions

Watched a couple of YouTube videos and then went at it

Removed mullion strip with Phillips screwdriver replaced spring reinstalled the mullion strip all in about 15 minutes.

Part Select had a great video which made the repair easy, using a putty knife to start removing the freeze door gasket. Once removed the install is simple just snap the new gasket into the track, but start at the corner. Other company's have a video requiring you to remove the entire freezer compartment out of the appliance, unnecessary waste of time and labor.

Removed two screws from door and three locking brackets with a small common screw driver. Raised the bracket, slide in the spring, held down the bracket, installed screws and plastic covers. Less than 2 minutes. Easy application no problem with the new spring or ,mullion..

This repair is pretty straight forward. Just remove the 3 screws that hold the ice maker and bin assembly in, unplug the wire harness connector, then remove it from the refrigerator door. Once removed you simply need to remove 3 more screws that hold the ice maker to the auger/bin frame, remove the temp sensor, and a couple pieces of tape. Re-assemble the new ice maker in reverse order and you are all set. I think part of the issue I was having was due to mineral buildup in the tray as well so it had a hard time cracking and removing the ice. Not sure why it was overfilling, maybe the sensor was broken or had buildup on it as well. This solved all the problems I was seeing and now it makes great ice that doesn't stick together and form a bridge in the bin.

easy repair. First step is you need to remove all food from bottom shelf and remove all three produce drawers. Then remove the meat drawer. You will need to lift the bottom self off the rail to remove. It is not heavy and does not need to be fully taken out of fridge - easier if you do but some what hard to get out.Unscrew the rail and unplug the old rail. Clean off the fridge - my fridge was gross behind the rail. Insert the rail into the fridge and then screw in the two screws. Place the bottom self back on the two rails and you are done.

Expensive to have repair man come out and find out that I’ve been mailed wrong spring again. My icemaker is on the left hand side this is the side of refrigerator- I need the spring for left side with the ice maker. Twice they have mailed me the Wrong spring that goes on the right hand side I have tried to explain this to the person that waits on me. Do I have to pay for another spring and mail this one back ?i have mailed one back and postage is getting expensive.

Very easy. Just slipped it back into place

Followed instructions online

I disconnected the refrigerator power, removed the 2 screws holding the mullion door on the left side of the refrigerator French-door (it’s the flap that allows the door to close). Removed the broken spring and installed the replacement spring in its place. Reinstalled the mullion door by putting it in place and installing the previously removed screws.

We pryed the ice dispenser housing out unscrewed the overlay from the relay board and then reversed the process to put it back in time consuming but went slow as not to brake tabs or crack housing

I actually didn't use what I got. Because there was all kinds of tubing coiled up in the door. We just fed the exsess all the way through the Fridge,and Bingo! It was done.

Unplug from wall receptacle. Pry switch out with screwdriver while pushing on inner tab. Then disconnect electrical plug.

The 2 minute or so video was not exactly matching the model that we had but the instructions were very good and important. The switch was a little difficult to get out from the side of the refrigerator.

1. Unplug the refrigerator (to avoid shock) 2. With one screwdriver pry open the switch on the side facing the door to a gap of about 1/8 inch 3. Insert a second screwdriver into the gap to press the plastic tab back slightly and this should release the part. 4. pull the part out and unplug it, you may have to pry back some small tabs on the sides, 5. Plug in the new switch 6. plug in the refrigerator the light should come on, if not tighten the connection 7. Insert new switch back into its slot, it should snap in place. Done!