LRSPC2331W LG Refrigerator - Instructions

I had previously watched a YouTube video (do this first!!) on a similar Kenmore model so I knew what to look out for: (1) turned off power, (2) took thin putty knife to slip under outer lip of switch (most screwdrivers are too thick), (3) wiggled switch at front end to release the tab, (4) unplugged from the socket, (5) plugged in new switch, (6) popped new switch back into door, (7) turned on power. Voila !! Super easy. I couldn't believe it.

I took a very thin bladed screwdriver and took the old part out -carefully.
The new part fit in quite easily.

Replaced old hose and installed the new one. Was very simple with the instructions in your email..... step by step, could not of been any similar.... you guys rock

First ,I unplug the refrigerator .
2nd i remove the back cover, clean the dust.
3th disconnect the water line, remove the all valve..
4th unplug all the wires and code ea with a No,remove the water lines
5th replace the valve reconnect the wires and water lines.replace the
back cover at last screw back the water line.check for water leaks .
i found ease the valve replacement installation.
.Thanks for the video.

Followed instructions online

I found a crack in the pex line from the valve up the back of the refrigerator to the water filter. I could not find the correct 5/16" size line locally to replace it. A guy in plumbing at Home Depot said he always repaired them by cutting out the crack and finding a piece of clear vinyl line that would fit tightly over the cracked pex to splice in a fix with hose clamps. I did that and it was a really bad idea. The line was obviously fatigued and failing because it just cracked further up and leaked again. I then looked up and ordered the correct line (actually both the supply and return since they were available). Installing the new lines was a breeze. The pex connectors are simple to disconnect and reconnect. Wish I had done that to start with. I looked for a youtube video for the proper replacement steps but all I found was a video of a guy who cut out a crack and stuck a pex connector in to replace the cracked section. By doing that he pulled slack from the valve end of the line which didn't exist and cracked the line again. I don't know why anyone would mess with patching one of these lines. The correct parts are available, cut to the right length, and removing and replacing them at the valve and the filter is dead simple.

The 2 minute or so video was not exactly matching the model that we had but the instructions were very good and important. The switch was a little difficult to get out from the side of the refrigerator.

Unplug from wall receptacle. Pry switch out with screwdriver while pushing on inner tab. Then disconnect electrical plug.

Really Easy

Used a small screw driver inserted into the front of the switch (facing the front) and pried until the switch was coming out. When out, I removed the connect harness and replace the switch with a new one.

1. Unplug the refrigerator (to avoid shock) 2. With one screwdriver pry open the switch on the side facing the door to a gap of about 1/8 inch 3. Insert a second screwdriver into the gap to press the plastic tab back slightly and this should release the part. 4. pull the part out and unplug it, you may have to pry back some small tabs on the sides, 5. Plug in the new switch 6. plug in the refrigerator the light should come on, if not tighten the connection 7. Insert new switch back into its slot, it should snap in place. Done!

Replace with new switch. this is the third switch i have replaced in 10 years. the only part, besides a light bulb, that has gone bad. obviously this is a problem with this model for Kenmore, or just poor switch design.

Easy install, small screwdriver under back of old switch push out and pull out with small pliers. unsnap the old plug and install new. YOUR DONE

Read previous tips
Taped off area around switch to protect surface
Used putty knife to extract switch
Used screwdriver to separate connector from switch
Plugged in connector
Pushed switch assembly into opening
Removed tape

Covered the sidewall with tape to protect. Pried the switch out with knife blade and removed electric plug with needle nose pliers. placed plug in new switch and pushed switch into the hole in the side wall. Took about five minutes.