LFC25760ST (ASTCLGA) LG Refrigerator - Instructions

Access to the main PCB is at the back of the fridge. Once the cover plate is off, notes were made of the cable connections though not truly necessary as the cable connectors are almost all at different sizes. Sharp nose pliers made removal of the connectors way easier. The new board fixed the problem as advertised.

Cover the putty knife with tape so you do not scratch the side wall where the switch is located. Slide the knife under the edge of the switch and push in a bit towards the switch and slightly twist to pop the switch out of its hole. Disconnect the wires from the switch and simply plug in the new switch. Push wiring back into the hole and careful push the switch into the hole until it snaps into place.

My son just pried out the old switch with a screw driver snapped out the old one and snapped in the new one. Pretty sure even I could have done this. Very quick and easy. Thanks. :-)

Remove door seal and cam shaft (one piece). Remove broken cam by removing Philips head screw. Replace broken cam with new cam and reassemble. The actual repair took about 15 minutes however the majority of time was spent figuring out that the door seal and cam shaft had to be removed, no tools required.

Removed the cover 2 screws
Squeezed the 2 side sleeves and removed
Snapped in new button, replaced the cover. Done

Unplugged the fridge. Used a screwdriver to loosen the switch. Easy to disconnect from fridge and just plugged the new switch in. Popped right back into the side of the fridge and worked perfectly.

slid screw driver under edge of switch, easy.

i first replaced valve as the water line hung up and broke the valve as i was moving fridge out,be careful about doing this,now i need to replace icemaker as its not working,ps it wasnt the water valve ,i broke it,so first replaced it now icemaker ,lg stinks for the 2 yrs icemaker has worked,my previous kenmore icemaker thru door worked for 23 yrs and was working the day i replaced it, the new electronic appliances are nice when they work!!!>Marvin

I popped the old switch out of place and then disconnected the wire harness from the switch with a pair of needle nose pliers. I then inserted the harness into the new switch and popped the switch into place. Super easy and fast.

While cleaning out the frig we removed the bottom shelf to remove the glass and really scrub it down. When we went to put it back in, my wife grabbed the crisper door front and snapped it offf. I immediately went to the computer to find a replacement part and found PartSelect.com. I plugged in the model number and I immediately saw a diagram to pick out my part. I had it ordered before she got all the food back in the frig! The part arrived early and I installed it in a matter of seconds. So easy to find the part, order it and install. You have a new customer!!!

Removal was pretty easy-- replacing crisper drawer took a little care so as not the snap off the hinge- thank you for the speed in which I got my part, no sooner did I order my part- it showed up at my door. your service was outstanding, put you in my favorites just incase I need to order again.

Replacing the broken part with the new part was really quite simple. The part just snapped in. The part was identical to the original. I must add that the web site was very easy to navigate, find the part, and order it. The part arrived very quickly. Guy

The repair was easy peasy! Just fit it all in. Shopping here was just as easy. I'd delayed doing it for so long because I thought it'd be laborious but I found my appliance fast and the parts I needed quickly. The diagram you provided with part numbers helped a lot. Thanks for making it easy.

Tape off the light button so door alarm does not go off. Take off the clear light shield and remove the light bulbs. Be careful, bulbs may still be HOT!! With Phillips head screw driver unscrew the light plate assy. Drop it down in a comfortable position. Disconnect the connector, unscrew the thermal sensor and remove light assy. Install new light assy into light plate assy. There is no thermal senor in the new assy. Snap light plate assy back into place and install the two screws previously taken out. Install bulbs and clear cover. Remove tape from light door switches and you are done. Lights should go on and off when door buttons are pushed in and out.

I replaced the entire plastic frame to fix the drawers. I'm frustrated that the design requires that I do this. Removed the metal bar that actually provides the support for the front of the frame and the drawers, etc. Three screws to remove and re-install. Easy. After removing the drawers, I just gently bent the drawer cover hinges to slide them out of the frame and tilted the frame out of the fridge. The glass just came out easily as it's not attached with any clips. I had to work to remove the clear plastic panels but a little careful persuasion and I was able to white supports out of the way and remove the panels. Then I removed the aforementioned bar and replaced the glass re-installed the whole assembly.