LSC27910ST LG Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- James from Bremerton, WA
- Parts Used:
- MEA40002602, MEA40002601
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Rails broke when overloaded
Removed shelf that rails were mounted to. Used a std phillips screwdriver to loosen screws attaching the rails, three per side. Removed damaged rails, lined up new rails and tightened screws. Returned shelf to refrigerator and inserted tray on the new rails.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Keith from Phoenix, AZ
- Parts Used:
- 4987JJ1010M, 4987JJ1010L
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
gaskets worn out again
replaced gaskets for the second time in four years
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Parkland, FL
- Parts Used:
- MEA40002602, MEA40002601
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Both guide rails had cracked at the front end I guess do to excessive weight in the drawer.
Simply removed the drawer, then removed the shelf above which held the guides, removed the guides ( 3 screws per side )and replaced them.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Willard from COMPTON, CA
- Parts Used:
- ADQ72910911
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Recommended change interval for water filter.
Remove top shelf. Screw out old filter and install new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Toai from Monroe, WA
- Parts Used:
- 6421JB2002R
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The ice maker door stay open. And not close back.
So easy that my 13 years old son replaced it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- wendy from west chester, PA
- Parts Used:
- MEA40002602, MEA40002601
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The rails for our cheese drawer broke
Just unscrew screws from old rails (still in refridgerator ), and screw them into new rails. We tried to order these parts from another online part site and we got the wrong parts. Partselect.com had drawing of our fridge and it was very easy to navigate through the web site. Thank you!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kim from West Mifflin, PA
- Parts Used:
- J756-00008B, 4680JB1026H
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Motor wouldn't work to turn the fan to keep fridge cool.
I am a woman and I did this in about 10 mins. I turned off the water, disconnected the water line, took the back off the fridge, disconnected the motor plug and unscrewed the fan. It took a little maneuvering to get the fan out but once I did it was a breeze. Opened up back door that housed the motor, took the motor out and put in the new one. Put everything back together and it's working great. Very fast shipping so don't pay for the expedited way to ship. I ordered Sunday night and it was in my door by 10:00 Tuesday morning.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Darryl from Rowlett, TX
- Parts Used:
- 5901JA1012B, 4974JA1044A, 4680JB1026H
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Bad fan motor and fan support assembly
The fan motor is easy to replace after the lower cover on the back of the refrigerator is removed. There is a drain tube (1 screw) that has to be removed in order for the fan support to be removed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Nolensville, TN
- Parts Used:
- 3390JA1150A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Ice tray was bent and spilling water onto ice making it freeze
I took the ice out with one screw and took out the old tray the new one slipped right in and I hooked up the little heat strip with one snap works perfect cost $10 I was told by appliance repair tech that I needed to replace the ice maker for $450 saved $440 dollars replacing the bent or warped ice tray
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nicholas from Melborne, FL
- Parts Used:
- 5221JA2006D
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Wrench set
Threads were striped on water valve leaked needed new one
Shut water valve off drained water in refrigerator instAlled new valve
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Eagle, WI
- Parts Used:
- 5989JA1002D, 3550JA3095A, 3390JA1150A
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Ice cubes did not drop out of tray when the ice maker cycled
1) Take out 3 screws from top of icemaker. 2) Unplug electrical connector from wiring harness. 3) Remove icemaker unit from freezer and then remove frozen cube sensor with clip and rear insulation. 4) With your hands pull cube tray motor out of the holding clips with the tray- if this is too difficult, spread bracket and only remove the tray from the unit. 5) Insert new tray into slots and install new or existing ice sensor, insulation, and sensor clip. 6) Reinstall icemaker unit to ceiling of freezer, don't forget to plug into wiring harness. 7) Turn unit on and make some ice!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sarah from Elk Grove, CA
- Parts Used:
- 4932JA3002A
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers
Each time we've had to move we have to remove the doors from the fridge to get it thru the front door.since water and ice run thru the freezer door there are 2 tubes that connect at the bottom of the freezer door that aren't meant to be separated very often if ever.it's easier to cut the tubing on b
With alot of elbow grease and a pair of pliars we managed to get the old connector off wo cuttig the tubing as the tubing was getting to short from being cut once to many times & there was no more play in the length.Original connector was a different color and shapped slightly different than the new one so was a bit concerned that I had ordered the wrong part but it went one very easily & did not leak. We even managed to remove it again just to see if it was possible wo cutting again. it came off with no trouble.I would say the replacement part was a better fit than the original simply because we could remove it easily wo having to cut the tube!
Was this instruction helpful to you?
Thank you for voting!