LFD21860ST (ASTCLGA) LG Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Thomas from Bay Shore, NY
- Parts Used:
- EAG62831801
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Interior Light Would Not Turn Off
Tape off the light button so door alarm does not go off. Take off the clear light shield and remove the light bulbs. Be careful, bulbs may still be HOT!! With Phillips head screw driver unscrew the light plate assy. Drop it down in a comfortable position. Disconnect the connector, unscrew the thermal sensor and remove light assy. Install new light assy into light plate assy. There is no thermal senor in the new assy. Snap light plate assy back into place and install the two screws previously taken out. Install bulbs and clear cover. Remove tape from light door switches and you are done. Lights should go on and off when door buttons are pushed in and out.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Reginald A. Green from Pelham, AL
- Parts Used:
- 4430JJ2004B, 4430JJ2004A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Plastic door latch/ cam shaft broke on left side door
Removed white plastic trim and installed new latch / cam shaft
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- LORI from INDIANAPOLIS, IN
- Parts Used:
- 3551JJ2019D
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
not a problem
snap it on!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Phillip from knoxville, TN
- Parts Used:
- 3551JJ2021A, 3551JJ2019D
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Tray Cover was broken where it attaches to the refrig. This is the Third one in 6 years
The plastic is real weak and the articulation point is not manufactured strong. You have to put one end in a female receiver and flex the tray cover with your fingers crossed hoping it won't snap, while sliding the other side into a similar female receiver on the other side. The Crisper drawer front has not come in yet. Disappointed that you have to buy the entire drawer with a front instead of the front. This is the 2nd one I have replaced. The difference in the Drawer Front...$10.00 and then entire Front and Drawer, $45 plus...
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Pat from West Bend, WI
- Parts Used:
- MDS64172918
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The gasket on our bottom drawer freezer was torn
Simply used a flat head screwdriver to get the first few inches of the gasket out of its track and after that just pulled it by hand. New gasket slipped over the door, lined up the corner and pressed into in the track. Checked to see that it was snug all over and we were done. 5 minutes at the very most. Never would have noticed this. Took all the bins out of the freezer to give it a good cleaning and noticed the torn piece hanging. Our refrigerator runs much less often. Expect to see a difference in our electric bill!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roman from West Chester, PA
- Parts Used:
- 3551JJ2019D
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broken hinge
Removal was pretty easy-- replacing crisper drawer took a little care so as not the snap off the hinge- thank you for the speed in which I got my part, no sooner did I order my part- it showed up at my door. your service was outstanding, put you in my favorites just incase I need to order again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kevin from Reno, NV
- Parts Used:
- 3551JJ2019D
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Crisper Drawer broke on right hinge
Replacement part from PartSelect was OEM, identical to original part. Installation was very quick. Inserted hinge on left side and then depressed the right side to slip it into place. Presto, it was done. Most impressed with PartSelect on the OEM replacement part and very prompt delivery.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donna from Abilene, TX
- Parts Used:
- 3550JJ1070B, 3110JJ1014A
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Lamp cover and case had melted
I removed the old lamp cover and case. Discovered that the last repair person had not re installed it correctly so the case had melted from the bulbs. I Removed the screws that was supposed to hold it up, assembled the case and cover, inserted the screws and anchored them in where they belong. Problem solved!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Walter from Vero Beach, FL
- Parts Used:
- 6600JB3007E, 3550JJ1070B, 3110JJ1014A
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Lights Stayed on Melted Light cover
Replaces door switches - removed screw from door hinge cover, lifted cover and removed switch. Plugged in new switch and reversed process. Removed screws from light bracket. Attached new frame to slots in roof and used screws to attach. Clipped on light cover.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cedric from Milwaukee, WI
- Parts Used:
- AAP73871501
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broken door
Simple replacement part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brian from Troutdale, OR
- Parts Used:
- 6600JB3007E, 3550JJ1070B, 3110JJ1014A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
the lights inside the frig weren't shutting off
the lights melted the lamp case and cover. I determined it was the switch ,but there was 2 of them . I replaced both . I used a screw driver to pry the covers off the switches which are on the top of the unit .Then I press the tabs on the switch and pulled it out. Slip the wire connect off. slip the wire connect on new switch press it in till the tabs snap in ,put covers back on. the lamp base and cover had two screws holding them, pull the screws slip the old melted base and cover. snap the new base and cover in and put the screws in done!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- G.J. from WHITE BIRD, ID
- Parts Used:
- 6600JB3007E, 3550JJ1070B, 3110JJ1014A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Lights in upper refrigerator would not turn off with doors closed
replaced melted light covers, replaced switches, and found another problem with power circuit board relay, on order now!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lisa from Santa Fe, NM
- Parts Used:
- 3551JJ2021A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broken part
replace piece
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Johnny from Acworth, GA
- Parts Used:
- 3551JJ2019D
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broke the crisper drawer front
While cleaning out the frig we removed the bottom shelf to remove the glass and really scrub it down. When we went to put it back in, my wife grabbed the crisper door front and snapped it offf. I immediately went to the computer to find a replacement part and found PartSelect.com. I plugged in the model number and I immediately saw a diagram to pick out my part. I had it ordered before she got all the food back in the frig! The part arrived early and I installed it in a matter of seconds. So easy to find the part, order it and install. You have a new customer!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brent from Cordele, GA
- Parts Used:
- 3551JJ2019D
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
mounting tabs broken off
slightly depressed tabs, lined up to mounting holes, released tabs.
Was this instruction helpful to you?
Thank you for voting!