LRFC22750SW LG Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Charlie from Huntsville, TX
- Parts Used:
- 5220JB2010T
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
Water was leaking into the ice maker and into the ice bucket
I removed the cover from the rear of the unit, with a screwdriver. Then with a adjustable wrench unscrewed the top nut of the water valve.I then removed the screw holding the valve to the wall of the fridge. Turned the valve upside down and removed the line going up to the ice maker. No tools needed here as it is a quick connect fitting.Use reverse order to install valve.I am 65 years old and if I can do this anyone can. Good luck from TX.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nancy from Hallandale Beach, FL
- Parts Used:
- 6600JB3007A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
light was not going on sometimes, or needed wiggling to work
purchased a new switch. The old switch just needed to be lightly pried out with a screw driver, then it was simple to unplug the old, and plug in the new. Voila! Light !
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from San Jose, CA
- Parts Used:
- 6600JB1010A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Unit kept beeping as if the freezer door was open
I popped the old switch out of place and then disconnected the wire harness from the switch with a pair of needle nose pliers. I then inserted the harness into the new switch and popped the switch into place. Super easy and fast.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Teresa from Miami, FL
- Parts Used:
- 4004JA3002A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- More than 2 hours
Frost in the freezer. Icemaker frozen.
I called LG and followed the instructions given over the phone. The instructions couldn't have been simpler. Disconnect the appliance for several hours and then connect again. I disconnected the appliance overnight, cleaned out the freezer, and reconnected it. Problem solved. Did not need to call a repairman and did not use the clips.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jerry from Boise, ID
- Parts Used:
- 3550JJ1033A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Cracked Support Bracket Would Not Allow Smooth Sliding Of Vegetable Tray.
Lifted the old one out, set the new one in!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gregory from Dubuque, IA
- Parts Used:
- 3581JJ8057K
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
Needed to replace the left side door due to dents incurred during a remodel
It was easy to remove the door by simply loosening the top hinge and simply lifting it off the bottom bracket. It was also easy to remove the door handle by tapping it from the bottom with a rubber mallet. This model handle had no outside "set screws" so it took some head scratching to figure it out. I gave up and visited the dealership for advice. I was a bit surprised there were no instructions included with the new door, but we got r dun.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JASON from GULFPORT, MS
- Parts Used:
- 5218JJ3001A, 4981JJ2001A, 3550JJ1033A
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
broken plastic supports
turned it off. took out the old and set the new in place. no tools required but did have to "pop" stuff into place. it was fairly awkward to do. Also would like to have replaced veggie bins They are cracked but these are not available. Only problem was figuring out what to order from the exploded diagram. It is very small on the computer screen and part numbers are difficult to read even with a magnifying glass
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Bay Shore, NY
- Parts Used:
- EAG62831801
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Interior Light Would Not Turn Off
Tape off the light button so door alarm does not go off. Take off the clear light shield and remove the light bulbs. Be careful, bulbs may still be HOT!! With Phillips head screw driver unscrew the light plate assy. Drop it down in a comfortable position. Disconnect the connector, unscrew the thermal sensor and remove light assy. Install new light assy into light plate assy. There is no thermal senor in the new assy. Snap light plate assy back into place and install the two screws previously taken out. Install bulbs and clear cover. Remove tape from light door switches and you are done. Lights should go on and off when door buttons are pushed in and out.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kenneth from Jeffersonton, VA
- Parts Used:
- 3550JA1388B
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
top light cover was warped. Simply replaced it with another.
Inserted it with my hands.
Was this instruction helpful to you?
Thank you for voting!