GML277UVQH (AWB2LGA) LG Refrigerator - Instructions

To replace the warped tray, I found the service manual (pg. 124 below) which took some interpreting.
Removed the lever. Then removed the assembly by two screws that are forward to the unit and go upwards.
The insulation, sensor, and sensor cover are simply pulled down and off and the unit separated to removed the tray, and then insert the new tray. Proceed in reverse. Takes only a few minutes.

/Users/grf/Desktop/fridge ice tray.pdf

Took off door per normal instructions.
Removed the old stopper and hinge assembly (the hard rubbery parts had worn enough against each other to cause the annoying sound when opening and closing the door).
Inserted the new stopper and hinge assembly.
There was no locking nut on the newer part, so just had to level the fridge door without that part of the instructions (from normal LG instructions)
Overall easy for a non-handy person and the annoying sound is gone.
Wife is happier now.

First ,I unplug the refrigerator .
2nd i remove the back cover, clean the dust.
3th disconnect the water line, remove the all valve..
4th unplug all the wires and code ea with a No,remove the water lines
5th replace the valve reconnect the wires and water lines.replace the
back cover at last screw back the water line.check for water leaks .
i found ease the valve replacement installation.
.Thanks for the video.

Removed ice dispenser and display with small screwdriver from front of the fridge. Pried out the whole piece slowly. This exposed the motor that activates the chute. Plugged in the new motor before any removal to verify the motor was the problem. When it worked, removed old and installed new. 3 screws. Piece of cake.

Replaced water pump assembly, all compression fittings easy to put together

Just replaced the old shelves with new

It was a "snap to complete it" inasmuch as the part just snapped in.

Removed the cover 2 screws
Squeezed the 2 side sleeves and removed
Snapped in new button, replaced the cover. Done

unfortunately my fridge stopped working. I purchased another but wanted to try and repair the old one. when ew one arrived, the old one was supposed to be put in garage but instead was hauled away. Had delivery return next day but they had as already removed and lost the handle screw for the bottom freezer and the screw that holds handle in place. ordered the handle screw and picked up the nut. very simple to install the screw and put handle back on.

Remove push plate for water/ice maker switch, remove 2 screws and 2 wires for switch. Replace with new.

Changed door switch. Repair worked for a few days but re-occured. Possibly the other switch is bad .

Not the fault of partselect. The manufacturer had decided to modify my part and still specifying that it was the NEW part number and that it was the direct replacement (shame on LG). Well its not the same part. The partselect CSR worked with me to try and find the previous design to no avail, even going so far as to give me the phone number of an obsolete parts seller... wow! Without a whimper parts select credited my account for the part that would not fit!! Without a doubt I will use them again. Way to stand behind your sale!! And also I got the parts within two days, amazing. The ones that did fit were well packed in perfect condition and on time. DON'T HESITATE TO USE THIS COMPANY

The part was extremely easy to replace. The unit came out with one screw, and I had to unplug the wire connection. After removing I noticed the ice tray was cracked - that's what caused the problem. The new unit went in easily with 1 plug in connection and 1 screw. I was done in less than 10 minutes.

I took the ice out with one screw and took out the old tray the new one slipped right in and I hooked up the little heat strip with one snap works perfect cost $10 I was told by appliance repair tech that I needed to replace the ice maker for $450 saved $440 dollars replacing the bent or warped ice tray

Shut water valve off drained water in refrigerator instAlled new valve