GML277UTRY (ATICLGA) LG Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Alan from Sun City West, AZ
- Parts Used:
- 4970JA3011K
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Spring was broken on original unit, had to replace whole lever.
removed old lever ( 2 screws ) took apart electrical connection, replaced lever, connected electrical hookup, put in screws. DONE !!!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Toai from Monroe, WA
- Parts Used:
- 6421JB2002R
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The ice maker door stay open. And not close back.
So easy that my 13 years old son replaced it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- dorothy from SALISBURY, MD
- Parts Used:
- MJB63190001
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
replace hand screw
unfortunately my fridge stopped working. I purchased another but wanted to try and repair the old one. when ew one arrived, the old one was supposed to be put in garage but instead was hauled away. Had delivery return next day but they had as already removed and lost the handle screw for the bottom freezer and the screw that holds handle in place. ordered the handle screw and picked up the nut. very simple to install the screw and put handle back on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- steve from clarence center, NY
- Parts Used:
- 5989JA1005D
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
My ice maker overflowed water and made a mess in the freezer
The part was extremely easy to replace. The unit came out with one screw, and I had to unplug the wire connection. After removing I noticed the ice tray was cracked - that's what caused the problem. The new unit went in easily with 1 plug in connection and 1 screw. I was done in less than 10 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Nolensville, TN
- Parts Used:
- 3390JA1150A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Ice tray was bent and spilling water onto ice making it freeze
I took the ice out with one screw and took out the old tray the new one slipped right in and I hooked up the little heat strip with one snap works perfect cost $10 I was told by appliance repair tech that I needed to replace the ice maker for $450 saved $440 dollars replacing the bent or warped ice tray
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sarah from Elk Grove, CA
- Parts Used:
- 4932JA3002A
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers
Each time we've had to move we have to remove the doors from the fridge to get it thru the front door.since water and ice run thru the freezer door there are 2 tubes that connect at the bottom of the freezer door that aren't meant to be separated very often if ever.it's easier to cut the tubing on b
With alot of elbow grease and a pair of pliars we managed to get the old connector off wo cuttig the tubing as the tubing was getting to short from being cut once to many times & there was no more play in the length.Original connector was a different color and shapped slightly different than the new one so was a bit concerned that I had ordered the wrong part but it went one very easily & did not leak. We even managed to remove it again just to see if it was possible wo cutting again. it came off with no trouble.I would say the replacement part was a better fit than the original simply because we could remove it easily wo having to cut the tube!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Darryl from Rowlett, TX
- Parts Used:
- 5901JA1012B, 4974JA1044A, 4680JB1026H
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Bad fan motor and fan support assembly
The fan motor is easy to replace after the lower cover on the back of the refrigerator is removed. There is a drain tube (1 screw) that has to be removed in order for the fan support to be removed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nicholas from Melborne, FL
- Parts Used:
- 5221JA2006D
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Wrench set
Threads were striped on water valve leaked needed new one
Shut water valve off drained water in refrigerator instAlled new valve
Was this instruction helpful to you?
Thank you for voting!