GMB208JSCA (ASTCLGY) LG Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- ROSEMARY from STOCKHOLM, NJ
- Parts Used:
- 4980JJ1016A, 3551JJ1005X
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The cover assembly was broken
Following the instructions
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Genevieve from MADERA, CA
- Parts Used:
- 4975JJ2028C
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Plastic runner had broken
removed 2 screws and replaced them on new part. Very easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stacy from ST AUGUSTINE, FL
- Parts Used:
- 5210JA3005W, 5040JA2015A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
The part did not fit
Like the customer who put a review on your site before me, I was unable to complete the repair because the inlet tube did not fit my refrigerator. I was hoping to speak to someone regarding this issue.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from NEWPORT NEWS, VA
- Parts Used:
- 5220JB2010T
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers, Wrench (Adjustable), Wrench set
The ice maker fill valve died.
Went on line to see how difficult it would be to replace the valve. Through Google there was a video which showed in exact detail how to remove and replace the valve. Then went on line to find the replacement part which was readily available. The only problem was that the connection on the valve where the fill water enters the valve was larger than the old valve. To fix that I went to a local Ace hardware store and found a nut that would fit the valve connection. Also don't forget to use a compression ring to keep the fill line secured when replaced.
Over all it was very simple and was in my "pay grade"
Over all it was very simple and was in my "pay grade"
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- shirley from ONALASKA, WI
- Parts Used:
- 6600JB1010A
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Light switch for refrigerator not functioning
Followed instructions online
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Fred Lee from BOTHELL, WA
- Parts Used:
- 4980JJ1016A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
The shelf that holds the crisper drawers had cracked and finally broken.
Bought a new shelf. Bought a center support (new), Put the new center support in the shelf. Removed glass, old shelf and drawers. Replaced the broken shelf by hooking the new one in to existing supports. Replaced glass. Replaced drawers.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sidney from ENDICOTT, NY
- Parts Used:
- 6600JB1010A
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The switch became intermittent - Possibly a poor designe
Used a small screw driver inserted into the front of the switch (facing the front) and pried until the switch was coming out. When out, I removed the connect harness and replace the switch with a new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JON from OJAI, CA
- Parts Used:
- 6600JB1010A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
INTERIOR DOOR ACTIVATED LIGHT SWITCH QUIT WORKING
1. Unplug the refrigerator (to avoid shock) 2. With one screwdriver pry open the switch on the side facing the door to a gap of about 1/8 inch 3. Insert a second screwdriver into the gap to press the plastic tab back slightly and this should release the part. 4. pull the part out and unplug it, you may have to pry back some small tabs on the sides, 5. Plug in the new switch 6. plug in the refrigerator the light should come on, if not tighten the connection 7. Insert new switch back into its slot, it should snap in place. Done!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cathrine from NEW ORLEANS, LA
- Parts Used:
- MEG54557902
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
The right hand glide for the top freezer drawer was broken.
Replaced the glide.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Philip from Ashland, MA
- Parts Used:
- 6600JB1010A
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Lights didn't come on when door was opened
I have moderate to good mechanical skills, but getting the old switch out was a sizeable challenge. Since this switch suffered some damage during extraction, I was lucky to have ordered a new one to replace it. Reinstall took approximately 90 seconds. PartSelect saved me an expensive service call.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gabriel from SACRAMENTO, CA
- Parts Used:
- EBR36222901
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Refrigerator no longer had power
Refrigerator seemed to have lost power. compressor wasn't on and no lights were on. Cricuit breaker checked out ok. Traced power with a voltage sensor to the main board on the back of the Fridge. Had power all the way to the PCB Assembly. Removed PCB board using pliers to pinch the mounting points. installed new board and reconnected all wires. Very easy. Fridge turned on after that. Success.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from STREATOR, IL
- Parts Used:
- MJB63029901, 4430JJ2005B
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Door stopper broke
Very simple, remove broken part with screwdriver and replace with new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Calvin from Northome, MN
- Parts Used:
- 6600JB1010A
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Light quit coming on when door opened.
Unplug from wall receptacle. Pry switch out with screwdriver while pushing on inner tab. Then disconnect electrical plug.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jesse from Pella, IA
- Parts Used:
- AJU55759303
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
Not making ice but could hear the solenoid trying to work
I turned off the water supply. Took off the access panel at the bottom of the fridge. Disconnected the waterlines from the valve. Remove the screw hole in the valve in place install the waterlines on the new valve attach the new valve to the refrigerator, reinstalled the back panel turn on the water And it made ice.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rita from GROSSE PT PK, MI
- Parts Used:
- 3551JJ1005X
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
Crisper cover broke.
It took me about 20min. Remove glass top and remove old support. Slide new support and glass.
Was this instruction helpful to you?
Thank you for voting!