LFX25974ST (02) LG Refrigerator - Instructions

1. Shut off water to refrigerator. 2. Removed bottom sheet metal cover (6 screws). 3. Removed leaking water inlet valve assembly from refrigerator (1 screw). 4. Remove water inlet tube (loosen nut) and tube back to refrigerator (pull from water valve after remove cotter pin washer). 5. Detach two electrical wire harnesses. 6. Install new water inlet valve assembly to refrigerator (1 screw). 7. Replace both water tubes to water inlet assembly. 8. Re-attach both wiring harnesses. 9. Turn water to refrigerator on. 10. Check for leaks. 11. Re-attach bottom sheet cover (6 screws).

I pulled the gasket off and installed the new one. It was very easy. All I had to do was to push the new gasket in place in the grooves in the door. The gasket I received was identical to the one I replaced.

Unscered 2 screws, unplug electrical connection under the screws, slide her flap into grooves, realign screw holes , and rescrew in. Done.

So easy I couldn't believe I'd done it so quickly. Two minutes from start to finish. Pull the old one off and press the new one in.

Had to buy the entire door mullion because the spring broke, wasn't happy. Got the new part very quickly and it was a new replacement part number. Somewhat tentative. Took it out of the box and looked it over. No spring! Groan! Thought I got the wrong part. Flipped the bottom hinge and it snapped open, no need for a spring! Two screws, disconnect the wire harness, throw away the old, get new, connect the wire harness, connect hinges, put in two screws! Super easy. Watch the video for some pointers along the way.

Replace the ice container. There was a break in one of the things that held it in.

Saved me $175.00 to $250.00 for an appliance repairman to come to my house for this. Absolutely simple to do. Pull gasket from right side door, no tabs or screws. Replace with new gasket, simply push new in by hand. Left side door needs two screws removed from’ flap. Now, gently bump the bottom of the flap to lift the flap up only three inches or so. Remove the electrical connection tab under the metal plate that the two screws secured. Now, repeat what you did on the right side door. Simple!

Used putty knife to pry out the old gasket, pressed new one in place. Very easy, done quickly. About 10 minutes.

1) Remove three drawers and items sitting on glass shelf.
2) Remove glass shelf
3) Remove entire crisper plastic unit from refrig.
4) Unscrew 6 screws holding uprights with a philips head screwdriver.
5) Remove top frame and replace with new frame.
6) Replace 6 screws and tighten them.
7) Replace entire frame in refrig and replace 3 drawers and glass shelf.
8) Done

It was SO easy. No clamps or brackets. Grabbed the gasket with pliers to get started removing it - just pull it out of the deep groove inset around the perimeter of the door. Within one minute I had the old gasket removed. Started installing the new gasket by inserting the top right corner 1st (pushing the new gasket profile into the deep groove inset on the door). Working around the top and right side slowly inserting the gasket profile into the deep groove around the entire door. You may have to "adjust" a bit by pulling on the gasket but within 5 minutes I had the new gasket in-place never having to turn off the refrigerator. YouTube has great "how-to" videos. It's easy!

It was easy; just pull off the old gaskets and press in the new. Used the putty knife to help set the new gasket, but was really not needed. The flat shipping pack helped because there were no kinks or folds to worry about.

started in a corner of the door and pulled out the old gasket and inserted the new gasket by being sure to start each corner before pushing in the center so it fits good first. extremely easy.

Took the old gasket out, put the new one in

Pull out old seal with hands. Install new seal into channel by pushing seal into channel with you fingers.

Watched a YouTube video on how to replace the door flipper (mullion). Very easy to unscrew the plate and disconnect the electrical circuit. Then gently slide up the flipper and replace with a new one.