LFC25770ST (03) LG Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- George from WHITE BIRD, ID
- Parts Used:
- 4681JB1027C
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Blower motor out on condenser
followed detailed movie from Utube video
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stacy from ST AUGUSTINE, FL
- Parts Used:
- 5210JA3005W, 5040JA2015A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
The part did not fit
Like the customer who put a review on your site before me, I was unable to complete the repair because the inlet tube did not fit my refrigerator. I was hoping to speak to someone regarding this issue.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from BAYTOWN, TX
- Parts Used:
- MHL62931401
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 30 - 60 mins
Replacement of shelf glass
Make sure you remove the double crisper frame that the glass sits on to get both the glass and frame to room (same) temperature!!!!!as easy as that!!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Peter from Sewell, NJ
- Parts Used:
- 5218JA1010E
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Freezer frost accumulation
After noting frost in freezer Right rail started to jam. Noted freezer door was closing crooked. Rail replacement resolved issue. It had been frosting up for some time so Rail must have been broken for a while. Check door seals they were not closing flush.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William L from SUMAS, WA
- Parts Used:
- 6600JB1010A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
light didn't come on when the door was opened
I took a very thin bladed screwdriver and took the old part out -carefully.
The new part fit in quite easily.
The new part fit in quite easily.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- shirley from ONALASKA, WI
- Parts Used:
- 6600JB1010A
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Light switch for refrigerator not functioning
Followed instructions online
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Billy from AUGUSTA, GA
- Parts Used:
- 4987JJ2002S
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Seal was damaged
Have your wonderful Grandson do the repair work.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from TONAWANDA, NY
- Parts Used:
- 6600JB1010A
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
bad switch
The 2 minute or so video was not exactly matching the model that we had but the instructions were very good and important. The switch was a little difficult to get out from the side of the refrigerator.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from STEPHENVILLE, TX
- Parts Used:
- EBS61443363
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Broken freezer rail.
Took out tray , removed 2 screws, removed old rail and installed new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Philip from Ashland, MA
- Parts Used:
- 6600JB1010A
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Lights didn't come on when door was opened
I have moderate to good mechanical skills, but getting the old switch out was a sizeable challenge. Since this switch suffered some damage during extraction, I was lucky to have ordered a new one to replace it. Reinstall took approximately 90 seconds. PartSelect saved me an expensive service call.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from PENNSVILLE, NJ
- Parts Used:
- 6600JB1010A
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Switch stops working
Replace with new switch. this is the third switch i have replaced in 10 years. the only part, besides a light bulb, that has gone bad. obviously this is a problem with this model for Kenmore, or just poor switch design.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Calvin from Northome, MN
- Parts Used:
- 6600JB1010A
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Light quit coming on when door opened.
Unplug from wall receptacle. Pry switch out with screwdriver while pushing on inner tab. Then disconnect electrical plug.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Karen from GEORGETOWN, TX
- Parts Used:
- MAN38143001
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- More than 2 hours
Part was delivered broken
The past I ordered was broken upon delivery. I asked for a replacement and was refunded the charge. Tried to contact you but "due to covid" you aren't taking calls. Net result: I ordered the part from another source, got it, installed easily. Won't use you again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- BRENT from RENO, NV
- Parts Used:
- AEC73877602
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- 30 - 60 mins
Wrong parts sent twice. One of the parts was a substitute 2" too long
Unable to complete repair, had to send parts back
Part should have been PS11732074, but got PS11732704- wrong part
This was a substitute part and was 2" too long
Waiting for refund on this part. It cost me $14.50 to return it by UPS!!!
Part should have been PS11732074, but got PS11732704- wrong part
This was a substitute part and was 2" too long
Waiting for refund on this part. It cost me $14.50 to return it by UPS!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sidney from ENDICOTT, NY
- Parts Used:
- 6600JB1010A
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The switch became intermittent - Possibly a poor designe
Used a small screw driver inserted into the front of the switch (facing the front) and pried until the switch was coming out. When out, I removed the connect harness and replace the switch with a new one.
Was this instruction helpful to you?
Thank you for voting!