78094 (ABICSER) LG Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Charlie from Huntsville, TX
- Parts Used:
- 5220JB2010T
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
Water was leaking into the ice maker and into the ice bucket
I removed the cover from the rear of the unit, with a screwdriver. Then with a adjustable wrench unscrewed the top nut of the water valve.I then removed the screw holding the valve to the wall of the fridge. Turned the valve upside down and removed the line going up to the ice maker. No tools needed here as it is a quick connect fitting.Use reverse order to install valve.I am 65 years old and if I can do this anyone can. Good luck from TX.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jack from Ellenton, FL
- Parts Used:
- 6600JB1010A
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
light out
slid screw driver under edge of switch, easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from San Jose, CA
- Parts Used:
- 6600JB1010A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Unit kept beeping as if the freezer door was open
I popped the old switch out of place and then disconnected the wire harness from the switch with a pair of needle nose pliers. I then inserted the harness into the new switch and popped the switch into place. Super easy and fast.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- dorothy from SALISBURY, MD
- Parts Used:
- MJB63190001
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
replace hand screw
unfortunately my fridge stopped working. I purchased another but wanted to try and repair the old one. when ew one arrived, the old one was supposed to be put in garage but instead was hauled away. Had delivery return next day but they had as already removed and lost the handle screw for the bottom freezer and the screw that holds handle in place. ordered the handle screw and picked up the nut. very simple to install the screw and put handle back on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Teresa from Miami, FL
- Parts Used:
- 4004JA3002A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- More than 2 hours
Frost in the freezer. Icemaker frozen.
I called LG and followed the instructions given over the phone. The instructions couldn't have been simpler. Disconnect the appliance for several hours and then connect again. I disconnected the appliance overnight, cleaned out the freezer, and reconnected it. Problem solved. Did not need to call a repairman and did not use the clips.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Bay Shore, NY
- Parts Used:
- EAG62831801
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Interior Light Would Not Turn Off
Tape off the light button so door alarm does not go off. Take off the clear light shield and remove the light bulbs. Be careful, bulbs may still be HOT!! With Phillips head screw driver unscrew the light plate assy. Drop it down in a comfortable position. Disconnect the connector, unscrew the thermal sensor and remove light assy. Install new light assy into light plate assy. There is no thermal senor in the new assy. Snap light plate assy back into place and install the two screws previously taken out. Install bulbs and clear cover. Remove tape from light door switches and you are done. Lights should go on and off when door buttons are pushed in and out.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kenneth from Jeffersonton, VA
- Parts Used:
- 3550JA1388B
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
top light cover was warped. Simply replaced it with another.
Inserted it with my hands.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Janet from West Hempstead, NY
- Parts Used:
- 4975JJ2028D
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
sliding rail
I removed the broken rail & installed the new rail with a screw driver. The screws were located in somewhat difficult position. The rail works OK but has a tendency to stick & the tray holder sometimes slips out of the new rail.
Was this instruction helpful to you?
Thank you for voting!