LFC25760TT (ANTCLGA) LG Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Christopher from Portland, OR
- Parts Used:
- 3550JJ0009A
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The drawers were sagging on one side due to broken plastic tabs
I replaced the entire plastic frame to fix the drawers. I'm frustrated that the design requires that I do this. Removed the metal bar that actually provides the support for the front of the frame and the drawers, etc. Three screws to remove and re-install. Easy. After removing the drawers, I just gently bent the drawer cover hinges to slide them out of the frame and tilted the frame out of the fridge. The glass just came out easily as it's not attached with any clips. I had to work to remove the clear plastic panels but a little careful persuasion and I was able to white supports out of the way and remove the panels. Then I removed the aforementioned bar and replaced the glass re-installed the whole assembly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joyce from Spring Hill, FL
- Parts Used:
- 3550JJ0009A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
lower shelf frame broke (by vegetable bin)
just snapped in
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Phillip from knoxville, TN
- Parts Used:
- 3551JJ2021A, 3551JJ2019D
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Tray Cover was broken where it attaches to the refrig. This is the Third one in 6 years
The plastic is real weak and the articulation point is not manufactured strong. You have to put one end in a female receiver and flex the tray cover with your fingers crossed hoping it won't snap, while sliding the other side into a similar female receiver on the other side. The Crisper drawer front has not come in yet. Disappointed that you have to buy the entire drawer with a front instead of the front. This is the 2nd one I have replaced. The difference in the Drawer Front...$10.00 and then entire Front and Drawer, $45 plus...
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Phyllis from Bocca Raton, FL
- Parts Used:
- 3551JJ2019D
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broken
easy and quickly Thank you for your prompt delivery and excellant service
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cedric from Milwaukee, WI
- Parts Used:
- AAP73871501
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broken door
Simple replacement part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- LORI from INDIANAPOLIS, IN
- Parts Used:
- 3551JJ2019D
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
not a problem
snap it on!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Reginald A. Green from Pelham, AL
- Parts Used:
- 4430JJ2004B, 4430JJ2004A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Plastic door latch/ cam shaft broke on left side door
Removed white plastic trim and installed new latch / cam shaft
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brent from Cordele, GA
- Parts Used:
- 3551JJ2019D
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
mounting tabs broken off
slightly depressed tabs, lined up to mounting holes, released tabs.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Bay Shore, NY
- Parts Used:
- EAG62831801
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Interior Light Would Not Turn Off
Tape off the light button so door alarm does not go off. Take off the clear light shield and remove the light bulbs. Be careful, bulbs may still be HOT!! With Phillips head screw driver unscrew the light plate assy. Drop it down in a comfortable position. Disconnect the connector, unscrew the thermal sensor and remove light assy. Install new light assy into light plate assy. There is no thermal senor in the new assy. Snap light plate assy back into place and install the two screws previously taken out. Install bulbs and clear cover. Remove tape from light door switches and you are done. Lights should go on and off when door buttons are pushed in and out.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jim from Indian Harbour Beach, FL
- Parts Used:
- 3551JJ2019D
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken tab on hinge of drawer crisper
Replace the drawer crisper
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- cindy from lantana, FL
- Parts Used:
- 3551JJ2019D, 3550JJ0009A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
lower shelve frame had warped on one end of the lower shelf
Removed the support bar from the warped frame, which had 3 screws, then reattached the bar to the new frame. The criper drawer front lids was a simple snap in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Walter from Carson, CA
- Parts Used:
- 4987JJ2002P, 4987JJ2002N
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The gasket on both top doors were torn
I first took off a plastic trip strip which just popped off with a little pull. Then I pulled the gasket off slowly all around the perimeter of the door and snapped off the guide strip with the help of a screwdriver. I installed the gasket next first the guide strip then followed up with the pushing the gasket into the groove all around the door. Did the same procedure on the other door. The gaskets came very well packed and undamaged. It took approximately 2 weeks because one gasket was on back order. Thank you for your help with these parts. It would have cost me 3 times as much if the repairman performed this repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mike from Cedar Falls, IA
- Parts Used:
- 4931JJ2002B, 3551JJ2019D
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The LH top door latch broke.
At first, ordered only a latch only to discover the mounting strip had instead failed. Ordering parts wasn't difficult although the parts catalog graphic leaves a lot to desire. Once I figured out how to remove the strip (had to remove the seal first and no instructions existed), it was easy to snap out the old and snap in the new part. This sure beat the cost of paying a repairman. However I fear than most homeowners that aren't mechanically inclined wouldnt have been successful because of no instructions and the parts catalog that had poor detail and a very small size.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Frances D. from Oxford, OH
- Parts Used:
- 3551JJ2019D
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
Crisper Drawer Fronts Broken at Hinges
No installation instructions. I just took everything out of the shelf holding the drawers and figured it out myself. Unfortunately today's products are made with cheap brittle plastic. This is the second time I have ordered parts for this refrigerator from you and I am glad you are so efficient and shipped orders quickly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marla from Woodland Hills, CA
- Parts Used:
- 3550JJ0009A
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
The roller assemblies for drawers had snapped off the shelf
I removed the old shelf and disassembled all the parts, removing glass shelf, bins, doors, etc. for use with the new shelf frame. Unfortunately, I hadn't been able to find all the roller assemblies from the original shelf and didn't realize that they were not considered part of the shelf frame. So, after reassembling all the pieces that I had, I still needed to order one additional roller assembly and specialty screw. Knowing this up front would have saved me a nice chunk of time and additional shipping charges. Otherwise, the repair was pretty straightforward.
Was this instruction helpful to you?
Thank you for voting!