73059 (AWBCSE1) LG Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- William from VICKSBURG, MS
- Parts Used:
- MHY62044106
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The Mullion Strip Spring Broke
Removed mullion strip with Phillips screwdriver replaced spring reinstalled the mullion strip all in about 15 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kevin from DADE CITY, FL
- Parts Used:
- MHY62044106
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Left French Door would not close properly
Removed two screws from door and three locking brackets with a small common screw driver. Raised the bracket, slide in the spring, held down the bracket, installed screws and plastic covers. Less than 2 minutes. Easy application no problem with the new spring or ,mullion..
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Luis from San Antonio, TX
- Parts Used:
- EAU60783850
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The ice tray was cracked and leaking water
1. Remove 3 screws (2- bottom 1-middle)
2. Loosen 1 screw (top middle left)
3. Remove the whole assembly by pulling down carefully
4. Disconnect the multi-wire plug from the back of the door. It has a locking tab on top that you may have to use a flathead screwdriver to unlock, being careful
not to touch the wiring.
5. Reverse this procedure to install the new icemaker assembly.
2. Loosen 1 screw (top middle left)
3. Remove the whole assembly by pulling down carefully
4. Disconnect the multi-wire plug from the back of the door. It has a locking tab on top that you may have to use a flathead screwdriver to unlock, being careful
not to touch the wiring.
5. Reverse this procedure to install the new icemaker assembly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from CLEARFIELD, UT
- Parts Used:
- AEQ73110210
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Ice Maker Can’t Rotate/Discharge Ice
First, remove power to the refrigerator.
To replace the ice maker you first have to remove the back mounting assembly, which ice maker is attached to.
Only three Phillips head screws need to be removed: 2 on the bottom and 1 on the back of the ice maker mounting assembly. Do not remove the two diagonal Phillips head screws holding the dispenser motor on the reverse side of the mounting assembly.
As you pull out the mounting assembly to the front you will see a connector on the top inside, which must be unplugged. A narrow standard screw driver will help the connector lock to release; slide the screwdriver tip under the connector lock clip and it will allow the connector to be unplugged.
Once the ice maker mounting assembly is removed and placed on a flat surface it will be self evident as to how to remove and replace the ice maker. The 1” tape might be needed during the cable re-routing process. However you can reuse the original tape required to be removed during the ice maker remove and replace process, if possible.
Reinstall the ice maker mounting assembly in the reverse order it was removed.
Apply power to the refrigerator.
Cycle the ice maker to Off and then back to On. It may take an hour or two before the ice maker produces ice because the temperature inside the ice maker must reach “0” degrees Fahrenheit before it will begin making ice.
Pull the ice maker
To replace the ice maker you first have to remove the back mounting assembly, which ice maker is attached to.
Only three Phillips head screws need to be removed: 2 on the bottom and 1 on the back of the ice maker mounting assembly. Do not remove the two diagonal Phillips head screws holding the dispenser motor on the reverse side of the mounting assembly.
As you pull out the mounting assembly to the front you will see a connector on the top inside, which must be unplugged. A narrow standard screw driver will help the connector lock to release; slide the screwdriver tip under the connector lock clip and it will allow the connector to be unplugged.
Once the ice maker mounting assembly is removed and placed on a flat surface it will be self evident as to how to remove and replace the ice maker. The 1” tape might be needed during the cable re-routing process. However you can reuse the original tape required to be removed during the ice maker remove and replace process, if possible.
Reinstall the ice maker mounting assembly in the reverse order it was removed.
Apply power to the refrigerator.
Cycle the ice maker to Off and then back to On. It may take an hour or two before the ice maker produces ice because the temperature inside the ice maker must reach “0” degrees Fahrenheit before it will begin making ice.
Pull the ice maker
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Judy from EGG HBR TWP, NJ
- Parts Used:
- AGU74110903
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Fridge door wouldn’t shut
Took old door strip (spring broke) and installed new with spring It went well and was working in less than 5 minutes
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jodi from WINTER GARDEN, FL
- Parts Used:
- AEQ73110210
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
My ice maker wouldn't release the ice, nothing was frozen and the motor would just bind
I bought the ice assembly motor only, super easy to install, remove the three main screws, lift out assembly, detach the cable. Then remove the screws on the parts, lift the tape, redo everything in reverse and it works flawlessly!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Johnny from MOUNT OLIVE, AL
- Parts Used:
- AJU72992601
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Leaking
Swapped old one with new one. New one had extra plug not needed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Larry from GODDARD, KS
- Parts Used:
- AEQ73110210
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
The refrigerator ice maker needed replacing
The only tool required was a Phillips screwdriver. I disassembled the old icemaker and unplugged the electrical snap in device. I removed the ground wire. Then reversed the steps in replacing the refrigerator ice maker kit assembly. It took slightly over 30 minutes to remove and replace the ice maker.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steve from MUKWONAGO, WI
- Parts Used:
- EAU59551204
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Ice chute would not open.
Removed ice dispenser and display with small screwdriver from front of the fridge. Pried out the whole piece slowly. This exposed the motor that activates the chute. Plugged in the new motor before any removal to verify the motor was the problem. When it worked, removed old and installed new. 3 screws. Piece of cake.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Katherine from NEW PRT RCHY, FL
- Parts Used:
- MHL62691504
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- More than 2 hours
Broken shelf for the vegatable bins
The glass was ordered correctly. The part was too big for mt refrigerator. I tried to send it back, but I got no reply. I tried cutting the glass to size and it shattered. I wasted 60.00 and im disgusted with your company.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from ELLWOOD CITY, PA
- Parts Used:
- MHY62044106
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
The original spring in the mullion door broke
I disconnected the refrigerator power, removed the 2 screws holding the mullion door on the left side of the refrigerator French-door (it’s the flap that allows the door to close). Removed the broken spring and installed the replacement spring in its place. Reinstalled the mullion door by putting it in place and installing the previously removed screws.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- RODNEY from GERMANTOWN, TN
- Parts Used:
- AGU74110903
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Spring broken on front plate
Unscrew two Phillip screws on center hing , push frt plate down and replace.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Susan from SAFETY HARBOR, FL
- Parts Used:
- MHL62691504
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Previous glass shelf shattered into a million pieces while cleaning.
Just laid the shelf down. Fit like a glove!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Franck from ST PETE BEACH, FL
- Parts Used:
- EAU60783850
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Icemaker not working
Removed ice bin
Unscrew the 3 screws.
Lift ice maker for the bottom to remove it but do not pull it until the power is unplug from the part.
Install the new part the same way you removed the old part.
Turn the switch and waiting 48 hours before the ice bin start getting ice
Unscrew the 3 screws.
Lift ice maker for the bottom to remove it but do not pull it until the power is unplug from the part.
Install the new part the same way you removed the old part.
Turn the switch and waiting 48 hours before the ice bin start getting ice
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eugene from ENCINITAS, CA
- Parts Used:
- AEQ73110210
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Ice tray cracked
Removed the old one and replaced with new just remember do your do diligence watch YouTube videos makes repair a lot easier
Was this instruction helpful to you?
Thank you for voting!