LFX21976ST (ASTCNA3) LG Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- William from VICKSBURG, MS
- Parts Used:
- MHY62044106
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The Mullion Strip Spring Broke
Removed mullion strip with Phillips screwdriver replaced spring reinstalled the mullion strip all in about 15 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- MIKE from ATLANTA, GA
- Parts Used:
- AGU75188619
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Spring on old mullion fell out
Replaced with new mullion
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sonya from VAIL, AZ
- Parts Used:
- AGU75188619
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The spring on the mullion door broke for the last time
This was an incredibly easy repair! 1 phillips screwdriver and two screws. Disconnect the small adapter, and you are good to go!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William L from SUMAS, WA
- Parts Used:
- 6600JB1010A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
light didn't come on when the door was opened
I took a very thin bladed screwdriver and took the old part out -carefully.
The new part fit in quite easily.
The new part fit in quite easily.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from PENNSVILLE, NJ
- Parts Used:
- 6600JB1010A
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Switch stops working
Replace with new switch. this is the third switch i have replaced in 10 years. the only part, besides a light bulb, that has gone bad. obviously this is a problem with this model for Kenmore, or just poor switch design.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Wendell, NC
- Parts Used:
- ADX73550621, ADX73550624
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Dampness on gaskets, mold and mildew
on left side door, I had to remove the flapper (the piece that rotates when you close the door to allow right door to seal. very simple, remove the flapper hingelift up to get the flapper off the door and move it out of the way.
Remove both door gaskets by pulling them out with your hands. Not the orientation of the gaskets because you will have to install the new gaksets in the same orientation.
Press the new gasket in place, into the slot that goes around the inside of the door, by using two fingers to press it into place. Cntinue this all around then go back and press again to assure the gasket is fully seated.
In my case, replacing the gaskets did not solve the issue, but they needed to be replaced do to the condition. The moisture issue was resolve by replacing the flapper (mentioned above)
Remove both door gaskets by pulling them out with your hands. Not the orientation of the gaskets because you will have to install the new gaksets in the same orientation.
Press the new gasket in place, into the slot that goes around the inside of the door, by using two fingers to press it into place. Cntinue this all around then go back and press again to assure the gasket is fully seated.
In my case, replacing the gaskets did not solve the issue, but they needed to be replaced do to the condition. The moisture issue was resolve by replacing the flapper (mentioned above)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jim from WELLINGTON, FL
- Parts Used:
- AGU75188619
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Plate Assembly Spring Broken
Remove 2 screws holding to door. Slide assembly up. Unplug connector. Remove old Plate Assembly. Do reverse to reinstall. Plug connector. Push in wires. Slide plate on. Fasten screws. Done
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bryan from ADA, MI
- Parts Used:
- AEQ73110205
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Ice maker not making ice, ice tray overfills and cannot dump, ice sticks together and will not dispense
This repair is pretty straight forward. Just remove the 3 screws that hold the ice maker and bin assembly in, unplug the wire harness connector, then remove it from the refrigerator door. Once removed you simply need to remove 3 more screws that hold the ice maker to the auger/bin frame, remove the temp sensor, and a couple pieces of tape. Re-assemble the new ice maker in reverse order and you are all set. I think part of the issue I was having was due to mineral buildup in the tray as well so it had a hard time cracking and removing the ice. Not sure why it was overfilling, maybe the sensor was broken or had buildup on it as well. This solved all the problems I was seeing and now it makes great ice that doesn't stick together and form a bridge in the bin.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donald from CLEBURNE, TX
- Parts Used:
- MJU62070602
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Replaced hose and it was exactly what I needed.
Replaced old hose and installed the new one. Was very simple with the instructions in your email..... step by step, could not of been any similar.... you guys rock
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from BOWDOINHAM, ME
- Parts Used:
- ADQ36011715, AGF80300702
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers, Socket set
The hose that feeds the Ice Maker broke,right where it goes in the Fridge.
I actually didn't use what I got. Because there was all kinds of tubing coiled up in the door. We just fed the exsess all the way through the Fridge,and Bingo! It was done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Delores from WINNIE, TX
- Parts Used:
- MHY62044106
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers
This is the second time they have mailed me the wrong spring. I talked to someone the last time and explained everything About my refrigerator. I had a Repair man come and try to put this part on my refrigerator this time and he told me that this spring is not for this side of my door. The first tim
Expensive to have repair man come out and find out that I’ve been mailed wrong spring again. My icemaker is on the left hand side this is the side of refrigerator- I need the spring for left side with the ice maker. Twice they have mailed me the Wrong spring that goes on the right hand side I have tried to explain this to the person that waits on me. Do I have to pay for another spring and mail this one back ?i have mailed one back and postage is getting expensive.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Peter from Sewell, NJ
- Parts Used:
- 5218JA1010E
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Freezer frost accumulation
After noting frost in freezer Right rail started to jam. Noted freezer door was closing crooked. Rail replacement resolved issue. It had been frosting up for some time so Rail must have been broken for a while. Check door seals they were not closing flush.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Johnny from MOUNT OLIVE, AL
- Parts Used:
- AJU72992601
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Leaking
Swapped old one with new one. New one had extra plug not needed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- shirley from ONALASKA, WI
- Parts Used:
- 6600JB1010A
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Light switch for refrigerator not functioning
Followed instructions online
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tom from BLUFFTON, SC
- Parts Used:
- ADX73550624
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
Torn door gasket
Pulled old gasket off by hand. New gasket was easy to install by pushing it into molded cutout in refrigerator door.
Very satisfying to have no glitches in the seamless installation.
Very satisfying to have no glitches in the seamless installation.
Was this instruction helpful to you?
Thank you for voting!