LFX23961SW ((02)) LG Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Brent from ROGERS, MN
- Parts Used:
- 6600JB3001C
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Water/ice maker not working
Remove push plate for water/ice maker switch, remove 2 screws and 2 wires for switch. Replace with new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alice from Wimberley, TX
- Parts Used:
- 5231JA2006F
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The water filter needed to be replaced.
I screwed the old one out and replaced it with the new one. A no-brainer. The thing that was so amazing was that I ordered the filter on the intrnet and it arrived the very next day!!! I was very surprised and pleased with the very quick shipping!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jack from Ellenton, FL
- Parts Used:
- 6600JB1010A
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
light out
slid screw driver under edge of switch, easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nancy from Hallandale Beach, FL
- Parts Used:
- 6600JB3007A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
light was not going on sometimes, or needed wiggling to work
purchased a new switch. The old switch just needed to be lightly pried out with a screw driver, then it was simple to unplug the old, and plug in the new. Voila! Light !
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Vacaville, CA
- Parts Used:
- MJB63029901
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
refridge door stopper broken
easy, a screw driver repaired in a mintue
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George from WHITE BIRD, ID
- Parts Used:
- 4681JB1027C
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Blower motor out on condenser
followed detailed movie from Utube video
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- GREG from STILLWATER, NJ
- Parts Used:
- 4930JA3091A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Wrench (Adjustable)
plastic tube leaking at connector
Uncoupled the old connector, replaced with new connector and attached supply line. Repair easy with right part, prior to ordering the right part I had tried a compression fitting and it still leaked. U-tube and others demonstrating repair assured me I was on the right path.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Janet from West Hempstead, NY
- Parts Used:
- 4975JJ2028D
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
sliding rail
I removed the broken rail & installed the new rail with a screw driver. The screws were located in somewhat difficult position. The rail works OK but has a tendency to stick & the tray holder sometimes slips out of the new rail.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Bay Shore, NY
- Parts Used:
- EAG62831801
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Interior Light Would Not Turn Off
Tape off the light button so door alarm does not go off. Take off the clear light shield and remove the light bulbs. Be careful, bulbs may still be HOT!! With Phillips head screw driver unscrew the light plate assy. Drop it down in a comfortable position. Disconnect the connector, unscrew the thermal sensor and remove light assy. Install new light assy into light plate assy. There is no thermal senor in the new assy. Snap light plate assy back into place and install the two screws previously taken out. Install bulbs and clear cover. Remove tape from light door switches and you are done. Lights should go on and off when door buttons are pushed in and out.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dean from Intervale, NH
- Parts Used:
- 4930JJ2028A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Door latch (cam) at door top broke off from the gasket holder. Gasket was fine so only needed new holder.
Gasket held in place by plastic bezel. Remove bezel by carefully pulling it toward you. Held in place by plastic clips. May need to pry carefully near clips. Pull gasket away from front edge of door. Gasket holder held by plastic swivel pieces top and bottom. Snap these out. Slide the gasket holder off the gasket. Remove the screws and slip the metal rod out of the broken holder. Retain screws, plastic clips, and cam. Slide the rod into new holder adding plastic clips and cam. Replace screws. Slide holder back onto gasket. Snap plastic clips into slots, being careful to bend the springs back so they go into the channel. Replace bezel. See videos on replacing door gaskets.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- AMANDA from CHARLOTTE, NC
- Parts Used:
- 4890JL1002N
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Tempered glass broke during cleaning
PartSelect made it so easy for us. We found the glass online, paid for it and it was delivered a couple days later. Packaged well we took out the glass and placed it in where the broken one used to be in the shelf casing. Simple. Thanks to PartSelect we didn't have to spend crazy money to have someone else do this simple repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JAMES from SCOTIA, NY
- Parts Used:
- 4930JJ2028B
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Lh Door Cam Holder Broke
Caution removing plastic molding with putty knife or flat bar . Roll the gasket toward the inside of frig ,push old holder up carefully out of gasket. Half way out tilt holder back to avoid ceiling . Save old holder for template ,remove screw from bottom,push out rod ,caution clip is spring loaded, install in new holder in reverse,slide back into gasket(carefully)!!replace molding
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Harolyn from Simsbury, CT
- Parts Used:
- 4890JL1002N
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
without any warning when taking glass out for cleaning it just exploded
This was late on a Sunday afternoon. I immediately called the store where I purchased the refrigerator who told me to go on-line for any parts. So I went to PartSelect and was able to find the correct part very easily and then order it. It arrived on Thursday without having paid for any upgrade in shipping time.I am very impressed with this company.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barbara from Wildersville, TN
- Parts Used:
- 6615JB2005C
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Screw drivers
The fridge died and couldn't find right parts needed
I was told the mother board went out. Took a few months to finally get one myself after repairman didn't come through. It turned out not to be the motherboard that sears repairman tested it for and said that's what it needed. I found Parts select after going round and round with sears parts refusing to accept return. There prices were better, as well as shipping and it came so quick i thought it was over night. The controller assembly was not the problem so we have it for a spare now. It was the freezer fan but even after installing it nothing would work is why we ordered the controller assembly. after 2 days and about 7 hours of checking, taking apart, rechecking assembling by my determined electrician it turned out to be a loose wire. LOL hope this helps someone. I'm just glad to have my fridge again! Blessings!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sharon from Magnolia, NJ
- Parts Used:
- 3391JJ2018D
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken drawer
Replaced the broken drawer with the new one. More importantly, your service is incredible!!! I immediately called my son who has a broken dryer and told him, you must use this internet site. Your price beat the competitor by more than 50% cheaper!!!!! I am not kidding, 50%, now that is what I call great service. I will hold onto your information for future purchases. Thank you, thank you, thank you.
Was this instruction helpful to you?
Thank you for voting!