LFX25960SB (00) LG Refrigerator - Instructions

Video makes it look easy. Kenmore refrigerator does not have "groove" along the right hand side of switch that allows for pushing down on release. Used a thin screwdriver to get under to push while holding switch edge with pliers. Kept slipping. Tape sides to avoid scratching inside of refrigerator.

Turn off power, remove upper and lower drawers (may need to open upper refrigerator doors to remove large freezer bin,) remove drawer supports (upper and lower), remove rear freezer panel (trick is to loosen 4 screws on fan bumpout to get the panel to come free from the freezer side wall), test thermistor with multimeter (should have continuity or near zero resistance across 2 orange fuse wires) before cutting zip ties, cut zip ties holding Thermistor in place, remove old Thermistor, install new Thermistor, install new zip ties, replace rear freezer panel, install upper and lower drawer supports, install drawers, turn on power, should be fixed if error code doesn't return after 6 hours.

Shut off water supply. Disconnect main supply line. Remove rear lower panel on back of refrigerator. Remove all tubing clamps on back. Disconnect leaking tubing from water supply valve. Remove water filter and unscrew/remove water filter housing. Replace tubing - connect to water filter housing then to water supply valve. Reconnect filter housing and filter. Reinstall lower panel, then main water supply line, then all tubing clamps. Turn water back on and check for leaks after discarding several glasses of water to fill filter. Job complete!

Examined old ice maker. It is held by some Philips screws. There are many screws you don't need to unscrew so look carefully. Then disconnected th dual in line connector. There is a little push tab to squeeze to release. Then the ground is connected with a screw. It's a little hard to see but unscrew that. My replacement came with no instructions or screws so try not to drop the screws down in the netherlands of the fridge. The hardest part was maneuvering the icemaker to reattach the power and ground. Even with that pretty straight forward replacement.

I was unable to replace the shelf (no assembly required) because I was sent the incorrect part even though I gave the model #,
serial # and exact description and measurement to the agent to whom I spoke. Even worse, I was told that I was responsible for returning the part at my expense. Rather than risking getting another incorrect part I will have a replacement plexiglass made to fit my shelf.

The replacement part came in a timely manner and snapped right into place.

I followed the directions! It was so easy that I bought another switch for my sister's fridge (same as mine). Her light was out too!

Took out shelf were the drawer slides are, out of the fridge.
Took a look of broken plastic slides to see how they were mounted before unsnapping them off the shelf, also compared with new slides before continuing. Unsnapped broken plastic slides by pressing the plastic clips off the shelf, pressing with my fingers, no tools used.
Installed new slides the same way old slides were. Slides have a top and bottom, so make sure to compare before unsnapping them off. When aligned, they snap right in.
Installed the shelf back in the fridge with all the items that were on it, then slid the drawer back in and VIOLA! back like new.
VERY EASY, no tools needed for my fridge, not sure for different fridges.

Remove 2 screws and then disconnect wires to the bulb sockets. Reconnect the wires Reinstalled lamp case , tab end first then replaced the 2 screws and the Lens cover. In addition, I changed out the incandescent bulbs to a much cooler LED bulb.

The heavy work is moving the fridge, then take off the lower plans. Use a bowel or cup for screws and the water line connector spacers so you don't loos them.
undo connections holding water line, including the bottom brakes for the solenoid. Reuse the spring around the lower waterline to prevent external wear on the line.

NOTE: remove the waterline connector spacers and save!
NOTE: you must compress (not pull) the connect to then pull the waterline out of the connectors.
NOTE: You must also remove the water filter and housing inside the fridge but this is easy.
MOTE: Test the line for leaks by turning on the water and then using the door water. The filter will need to refill so it may take a minute before water comes up. This line only have pressure when the door water is used or the ice maker needs to make ice.


After replacing the line, test the line for leaks by using the door water so the solenoid fills the lines

I replaced solenoid, flapper heated door, and broken spring. Very easy instructions on "YouTube"

Compress the ends. It snaps in

Remove the crisper drawer for room to work, locate the two mounting holes at the top, front of the shelf, insert the plastic hinge pin on the outside wall side. Holding the front(cover0 in one hand, reach under the cover with your other hand, grasp the second hinge pin and move it to the insert position. Using your index finger, carefully bend the bracket arm to allow the pin to be inserted.

Have had the Sears repairman come to the house to replace this part in 5 minutes for +$100.. twice. When my dad's stopped working, ordered the part and replaced it myself for the cost of the part and shipping.
Use a screw driver to pry the right side of the switch and pull out. Best to watch a youtube video first. Takes about 5 minutes.

After watching a few iTunes videos I was able to order the light switch from part select and within a week I had the new switch. I had a little trouble getting the switch out. I used a flat screw driver and taped around the edge to keep from damaging the wall inside. I found the clip on the right side and had to use some force to get it popped out, you may need to use pliers to disconnect the switch.