LFX25950SW (00) LG Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Ronette D from KOKOMO, IN
- Parts Used:
- 4975JA2028A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
rail broke
slid out the old one and slid in the new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Keith from WAMEGO, KS
- Parts Used:
- 5220JB2008A
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench set
water valve was leaking
removed old unit and installed new unit. Instructions were very clear
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dana from Lakeside, AZ
- Parts Used:
- 5209JA1044A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Broken Fan motor
took out original Duct Assembly, put in NEW Duct Assembly the same way the original Duct Assembly was removed in the freezer. The rest was easy to put back together
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Patty Jo from ALDEN, NY
- Parts Used:
- AJP32871405
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Old tray was cracked and edge was breaking off
This is a mater of sliding the old tray out. Cleaning the tracks and sliding the new one in. I have had to replace the rollers on the previous drawer. But not this time. which that took approximately 20 minutes
Please note: while the drawer tray is out by cleaning the tracks it gets the little plastic particles off and makes the new one easier to slide. Really should be taken out and cleaned periodically so track and drawer slide easily anyway.
Please note: while the drawer tray is out by cleaning the tracks it gets the little plastic particles off and makes the new one easier to slide. Really should be taken out and cleaned periodically so track and drawer slide easily anyway.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from CURWENSVILLE, PA
- Parts Used:
- 6600JB1010A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Door light switch, 3rd one I have replaced in 6 years made in China.
Easy install, small screwdriver under back of old switch push out and pull out with small pliers. unsnap the old plug and install new. YOUR DONE
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dean from HILLSDALE, MI
- Parts Used:
- 6600JB1010A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Replace switch
Read previous tips
Taped off area around switch to protect surface
Used putty knife to extract switch
Used screwdriver to separate connector from switch
Plugged in connector
Pushed switch assembly into opening
Removed tape
Taped off area around switch to protect surface
Used putty knife to extract switch
Used screwdriver to separate connector from switch
Plugged in connector
Pushed switch assembly into opening
Removed tape
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Calvin from Northome, MN
- Parts Used:
- 6600JB1010A
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Light quit coming on when door opened.
Unplug from wall receptacle. Pry switch out with screwdriver while pushing on inner tab. Then disconnect electrical plug.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from TONAWANDA, NY
- Parts Used:
- 6600JB1010A
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
bad switch
The 2 minute or so video was not exactly matching the model that we had but the instructions were very good and important. The switch was a little difficult to get out from the side of the refrigerator.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Philip from Ashland, MA
- Parts Used:
- 6600JB1010A
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Lights didn't come on when door was opened
I have moderate to good mechanical skills, but getting the old switch out was a sizeable challenge. Since this switch suffered some damage during extraction, I was lucky to have ordered a new one to replace it. Reinstall took approximately 90 seconds. PartSelect saved me an expensive service call.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Linda from Canyon Lake, TX
- Parts Used:
- AJP32871405, 3551JJ2020G
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Replaced parts then repair people decided it was not repairable. Cost me have the cost of the parts to send back.
Easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephen from DICKINSON, TX
- Parts Used:
- MDS38201426
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Freezer door gasket needed replacing.
Simply removed old gasket. Started in a corner with installing the new gasket. It went in easily and quickly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Greg from CASA GRANDE, AZ
- Parts Used:
- 6600JB1010A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
door slight switch failed
Covered the sidewall with tape to protect. Pried the switch out with knife blade and removed electric plug with needle nose pliers. placed plug in new switch and pushed switch into the hole in the side wall. Took about five minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from CANON CITY, CO
- Parts Used:
- 3551JJ2020G
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
The base table which holds the two drawers at the floor of the refrigerator was cracked.
I removed the old table, removed the glass, as the new part did not come with glass and removed the front side support. I simply installed both the glass and support on the new part and re-installed the parts.
Couldn't be more simple!!!
Couldn't be more simple!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sidney from ENDICOTT, NY
- Parts Used:
- 6600JB1010A
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The switch became intermittent - Possibly a poor designe
Used a small screw driver inserted into the front of the switch (facing the front) and pried until the switch was coming out. When out, I removed the connect harness and replace the switch with a new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lawrence from FALL RIVER, MA
- Parts Used:
- 4620JJ2009A
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Door Stopper had snapped off
Unscrewed what remained from broken door stop, aligned new one, screwed it in. Done!
Was this instruction helpful to you?
Thank you for voting!