LFD25860ST (00) LG Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- john from locust valley, NY
- Parts Used:
- MJU62070602
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
water supply to ice maker leaked
Gave model number on website, found picture of icemaker section. Ordered part that came in 3 days and switched old for new
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from San Jose, CA
- Parts Used:
- 6600JB1010A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Unit kept beeping as if the freezer door was open
I popped the old switch out of place and then disconnected the wire harness from the switch with a pair of needle nose pliers. I then inserted the harness into the new switch and popped the switch into place. Super easy and fast.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jack from Ellenton, FL
- Parts Used:
- 6600JB1010A
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
light out
slid screw driver under edge of switch, easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- GREG from STILLWATER, NJ
- Parts Used:
- 4930JA3091A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Wrench (Adjustable)
plastic tube leaking at connector
Uncoupled the old connector, replaced with new connector and attached supply line. Repair easy with right part, prior to ordering the right part I had tried a compression fitting and it still leaked. U-tube and others demonstrating repair assured me I was on the right path.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Teresa from Miami, FL
- Parts Used:
- 4004JA3002A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- More than 2 hours
Frost in the freezer. Icemaker frozen.
I called LG and followed the instructions given over the phone. The instructions couldn't have been simpler. Disconnect the appliance for several hours and then connect again. I disconnected the appliance overnight, cleaned out the freezer, and reconnected it. Problem solved. Did not need to call a repairman and did not use the clips.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brent from ROGERS, MN
- Parts Used:
- 6600JB3001C
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Water/ice maker not working
Remove push plate for water/ice maker switch, remove 2 screws and 2 wires for switch. Replace with new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- G.J. from WHITE BIRD, ID
- Parts Used:
- 6600JB3007E, 3550JJ1070B, 3110JJ1014A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Lights in upper refrigerator would not turn off with doors closed
replaced melted light covers, replaced switches, and found another problem with power circuit board relay, on order now!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- cindy from lantana, FL
- Parts Used:
- 3551JJ2019D, 3550JJ0009A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
lower shelve frame had warped on one end of the lower shelf
Removed the support bar from the warped frame, which had 3 screws, then reattached the bar to the new frame. The criper drawer front lids was a simple snap in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brian from Troutdale, OR
- Parts Used:
- 6600JB3007E, 3550JJ1070B, 3110JJ1014A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
the lights inside the frig weren't shutting off
the lights melted the lamp case and cover. I determined it was the switch ,but there was 2 of them . I replaced both . I used a screw driver to pry the covers off the switches which are on the top of the unit .Then I press the tabs on the switch and pulled it out. Slip the wire connect off. slip the wire connect on new switch press it in till the tabs snap in ,put covers back on. the lamp base and cover had two screws holding them, pull the screws slip the old melted base and cover. snap the new base and cover in and put the screws in done!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Frances D. from Oxford, OH
- Parts Used:
- 3551JJ2019D
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
Crisper Drawer Fronts Broken at Hinges
No installation instructions. I just took everything out of the shelf holding the drawers and figured it out myself. Unfortunately today's products are made with cheap brittle plastic. This is the second time I have ordered parts for this refrigerator from you and I am glad you are so efficient and shipped orders quickly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Phillip from knoxville, TN
- Parts Used:
- 3551JJ2021A, 3551JJ2019D
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Tray Cover was broken where it attaches to the refrig. This is the Third one in 6 years
The plastic is real weak and the articulation point is not manufactured strong. You have to put one end in a female receiver and flex the tray cover with your fingers crossed hoping it won't snap, while sliding the other side into a similar female receiver on the other side. The Crisper drawer front has not come in yet. Disappointed that you have to buy the entire drawer with a front instead of the front. This is the 2nd one I have replaced. The difference in the Drawer Front...$10.00 and then entire Front and Drawer, $45 plus...
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Pat from West Bend, WI
- Parts Used:
- MDS64172918
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The gasket on our bottom drawer freezer was torn
Simply used a flat head screwdriver to get the first few inches of the gasket out of its track and after that just pulled it by hand. New gasket slipped over the door, lined up the corner and pressed into in the track. Checked to see that it was snug all over and we were done. 5 minutes at the very most. Never would have noticed this. Took all the bins out of the freezer to give it a good cleaning and noticed the torn piece hanging. Our refrigerator runs much less often. Expect to see a difference in our electric bill!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kevin from Reno, NV
- Parts Used:
- 3551JJ2019D
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Crisper Drawer broke on right hinge
Replacement part from PartSelect was OEM, identical to original part. Installation was very quick. Inserted hinge on left side and then depressed the right side to slip it into place. Presto, it was done. Most impressed with PartSelect on the OEM replacement part and very prompt delivery.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Johnny from Acworth, GA
- Parts Used:
- 3551JJ2019D
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broke the crisper drawer front
While cleaning out the frig we removed the bottom shelf to remove the glass and really scrub it down. When we went to put it back in, my wife grabbed the crisper door front and snapped it offf. I immediately went to the computer to find a replacement part and found PartSelect.com. I plugged in the model number and I immediately saw a diagram to pick out my part. I had it ordered before she got all the food back in the frig! The part arrived early and I installed it in a matter of seconds. So easy to find the part, order it and install. You have a new customer!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- william from mashpee, MA
- Parts Used:
- 4430JJ2004B, 4430JJ2004A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
broken
removed 1 screw and replaced
Was this instruction helpful to you?
Thank you for voting!