LFD25860ST ((00)) LG Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Todd from MARS HILL, NC
- Parts Used:
- MJU62070602
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Fridge waterline for ice maker / door water
The heavy work is moving the fridge, then take off the lower plans. Use a bowel or cup for screws and the water line connector spacers so you don't loos them.
undo connections holding water line, including the bottom brakes for the solenoid. Reuse the spring around the lower waterline to prevent external wear on the line.
NOTE: remove the waterline connector spacers and save!
NOTE: you must compress (not pull) the connect to then pull the waterline out of the connectors.
NOTE: You must also remove the water filter and housing inside the fridge but this is easy.
MOTE: Test the line for leaks by turning on the water and then using the door water. The filter will need to refill so it may take a minute before water comes up. This line only have pressure when the door water is used or the ice maker needs to make ice.
After replacing the line, test the line for leaks by using the door water so the solenoid fills the lines
undo connections holding water line, including the bottom brakes for the solenoid. Reuse the spring around the lower waterline to prevent external wear on the line.
NOTE: remove the waterline connector spacers and save!
NOTE: you must compress (not pull) the connect to then pull the waterline out of the connectors.
NOTE: You must also remove the water filter and housing inside the fridge but this is easy.
MOTE: Test the line for leaks by turning on the water and then using the door water. The filter will need to refill so it may take a minute before water comes up. This line only have pressure when the door water is used or the ice maker needs to make ice.
After replacing the line, test the line for leaks by using the door water so the solenoid fills the lines
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Darlene from MISSION HILLS, CA
- Parts Used:
- 3551JJ2019D
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Pops right in
Pops right In
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Deborah from PARMA, OH
- Parts Used:
- 3551JJ2019D, 3550JJ0009A
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Broken lower shelf frame and crisper drawer fronts had cracked
Removed screws and the plastic shelf tops from the broken shelf. These parts are sold separately. Do NOT throw anything away until you know you have what you need.
Gentle pull the shelf to spread it enough to get the plastic pieces in. This is the only hard part. Screw the slides onto the new frame. Snap the covers into the crisper fronts. You’ll want to force them in but don’t. They will snap and break.
Gentle pull the shelf to spread it enough to get the plastic pieces in. This is the only hard part. Screw the slides onto the new frame. Snap the covers into the crisper fronts. You’ll want to force them in but don’t. They will snap and break.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Mountain View, CA
- Parts Used:
- 3550JJ0009A
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
lower shelf needed replacement (cracked in front, thin drawer guides broken)
Food off top of shelf, drawers come out, glass tops come off, lift the whole unit up (can be a little heavy. Tilt sideways to angle past doors (remove door's lower bins as needed by removing food and lifting up). Turn upside down, remove 3 screws from metal rod and remove metal rod (may require prying out with screwdriver). Remove textured plastic top pieces from each side; some flexing is required to get one side up, then the other. Remove two hinged drawer covers by pinching in at their hinge points.
This is your last chance to clear all the walls, floor, and ledges at the bottom of your fridge. Just sayin'.
Put new shelf upside down on counter. Transfer metal rod to new shelf, screw it in. Transfer hinged drawer covers. Transfer textured plastic topic pieces, again putting one side (of each) in first and flexing unit a little to get other side in. Turn right side up and angle back into refrigerator.
Bring shelf flat and push to the back of the refrigerator until it is flush with the back. Lower whole unit until it rests on top of the side rails where drawers slide in. Left side has a tongue that will fit into a 2" or so notch near the front, right side will rest on top of a round bumper. Front coldness control should still operate smoothly. Put drawers in to make sure they glide and close smoothly. Put glass shelf on top and press down lightly to make sure lower shelf is stable and glass fits neatly into its plastic frame. Replace any door bins you removed.
Ta da!
This is your last chance to clear all the walls, floor, and ledges at the bottom of your fridge. Just sayin'.
Put new shelf upside down on counter. Transfer metal rod to new shelf, screw it in. Transfer hinged drawer covers. Transfer textured plastic topic pieces, again putting one side (of each) in first and flexing unit a little to get other side in. Turn right side up and angle back into refrigerator.
Bring shelf flat and push to the back of the refrigerator until it is flush with the back. Lower whole unit until it rests on top of the side rails where drawers slide in. Left side has a tongue that will fit into a 2" or so notch near the front, right side will rest on top of a round bumper. Front coldness control should still operate smoothly. Put drawers in to make sure they glide and close smoothly. Put glass shelf on top and press down lightly to make sure lower shelf is stable and glass fits neatly into its plastic frame. Replace any door bins you removed.
Ta da!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael G, from CENTENNIAL, CO
- Parts Used:
- 5231JA2006F
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The rails for one of drawers were replaced
Removed old rails and tapped new rails in place. The big problem was finding how to fix the drawer. After searching many online websites, It was my good fortune to find Partselect and a one of their service representatives who
knew how to fix my drawer
and they had the part.
knew how to fix my drawer
and they had the part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Art from GARNER, NC
- Parts Used:
- 6871JB1423N
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Lights stayed on when doors were closed.
Verified that the contact switches were good. Issue was in the main board. Pulled fridge out from wall. Unplugged fridge from wall socket.
Took out 3 screws holding cover of main board. Unplugged main board. Replaced main board and reconnected plugs to main board. Replaced cover with 3 screws. Pushed fridge back against wall.
Took out 3 screws holding cover of main board. Unplugged main board. Replaced main board and reconnected plugs to main board. Replaced cover with 3 screws. Pushed fridge back against wall.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donald from CLEBURNE, TX
- Parts Used:
- MJU62070602
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Replaced hose and it was exactly what I needed.
Replaced old hose and installed the new one. Was very simple with the instructions in your email..... step by step, could not of been any similar.... you guys rock
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- BRENT from RENO, NV
- Parts Used:
- AEC73877602
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- 30 - 60 mins
Wrong parts sent twice. One of the parts was a substitute 2" too long
Unable to complete repair, had to send parts back
Part should have been PS11732074, but got PS11732704- wrong part
This was a substitute part and was 2" too long
Waiting for refund on this part. It cost me $14.50 to return it by UPS!!!
Part should have been PS11732074, but got PS11732704- wrong part
This was a substitute part and was 2" too long
Waiting for refund on this part. It cost me $14.50 to return it by UPS!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from STEPHENVILLE, TX
- Parts Used:
- AEC73877601
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Broken freezer rail.
Took out tray , removed 2 screws, removed old rail and installed new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dave from San Diego, CA
- Parts Used:
- 3550JJ0009A
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Broken shelf
Replaced a new shelf
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Milton from WILTON, ME
- Parts Used:
- 3550JJ0009A
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Grams had cracked in front
Super easy. Removal of old shelf and 3 screws was obvious how to put in new shelf. Thank you. Excellent cost, delivery and ease of transaction.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from Goose Creek, SC
- Parts Used:
- 4430JJ2004B, 4430JJ2004A
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Right door cam broken
Remove door seal and cam shaft (one piece). Remove broken cam by removing Philips head screw. Replace broken cam with new cam and reassemble. The actual repair took about 15 minutes however the majority of time was spent figuring out that the door seal and cam shaft had to be removed, no tools required.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Awilda from Staten Island, NY
- Parts Used:
- MJU62070602
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The water line was leaking
Removed the damaged tube and replaced the it with a new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- john from locust valley, NY
- Parts Used:
- MJU62070602
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
water supply to ice maker leaked
Gave model number on website, found picture of icemaker section. Ordered part that came in 3 days and switched old for new
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alice from Wimberley, TX
- Parts Used:
- 5231JA2006F
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The water filter needed to be replaced.
I screwed the old one out and replaced it with the new one. A no-brainer. The thing that was so amazing was that I ordered the filter on the intrnet and it arrived the very next day!!! I was very surprised and pleased with the very quick shipping!!!
Was this instruction helpful to you?
Thank you for voting!