LFC25760SW ((00)) LG Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Craig from SPRING HILL, FL
- Parts Used:
- MDS38201426
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Ice crystals appearing on the face of the freezer draws
Part Select had a great video which made the repair easy, using a putty knife to start removing the freeze door gasket. Once removed the install is simple just snap the new gasket into the track, but start at the corner. Other company's have a video requiring you to remove the entire freezer compartment out of the appliance, unnecessary waste of time and labor.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Victoria from Oak Grove, KY
- Parts Used:
- 6600JB1010A
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Lights out on refrigerator
Unplugged the refrigerator, Taped around the edges of switch as I had read to prevent possible scratches, used very thin flathead screwdriver to pry out old switch, unplugged old switch, plugged in new switch, put it back in opening, plugged fridge back in, and I had beautiful light! Hardest part was unplugging the refrigerator!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stacy from ST AUGUSTINE, FL
- Parts Used:
- 5210JA3005W, 5040JA2015A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
The part did not fit
Like the customer who put a review on your site before me, I was unable to complete the repair because the inlet tube did not fit my refrigerator. I was hoping to speak to someone regarding this issue.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from TUCSON, AZ
- Parts Used:
- 6600JB1010A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Refrigerator light would not reliably turn on when the door was opened.
Switched the refrigerator circuit breaker to off. Put tape around the switch to prevent scratches. Wedged the putty knife into the right side of the switch and pried up.the switch and connector popped out. Removed the connector from the old switch and connected it to the socket in the new switch. Stuffed the new switch and connector back into its home. Switched on the circuit breaker. Now we have light in the refrigerator with every opening!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ernie from LEOMINSTER, MA
- Parts Used:
- 4987JJ2002P, 4987JJ2002N, 4430JJ2004B, 4430JJ2004A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
leakey door gaskets
viewed video and followed instructions was a piece of cake
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Peter from Sewell, NJ
- Parts Used:
- 5218JA1010E
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Freezer frost accumulation
After noting frost in freezer Right rail started to jam. Noted freezer door was closing crooked. Rail replacement resolved issue. It had been frosting up for some time so Rail must have been broken for a while. Check door seals they were not closing flush.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Mountain View, CA
- Parts Used:
- 3550JJ0009A
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
lower shelf needed replacement (cracked in front, thin drawer guides broken)
Food off top of shelf, drawers come out, glass tops come off, lift the whole unit up (can be a little heavy. Tilt sideways to angle past doors (remove door's lower bins as needed by removing food and lifting up). Turn upside down, remove 3 screws from metal rod and remove metal rod (may require prying out with screwdriver). Remove textured plastic top pieces from each side; some flexing is required to get one side up, then the other. Remove two hinged drawer covers by pinching in at their hinge points.
This is your last chance to clear all the walls, floor, and ledges at the bottom of your fridge. Just sayin'.
Put new shelf upside down on counter. Transfer metal rod to new shelf, screw it in. Transfer hinged drawer covers. Transfer textured plastic topic pieces, again putting one side (of each) in first and flexing unit a little to get other side in. Turn right side up and angle back into refrigerator.
Bring shelf flat and push to the back of the refrigerator until it is flush with the back. Lower whole unit until it rests on top of the side rails where drawers slide in. Left side has a tongue that will fit into a 2" or so notch near the front, right side will rest on top of a round bumper. Front coldness control should still operate smoothly. Put drawers in to make sure they glide and close smoothly. Put glass shelf on top and press down lightly to make sure lower shelf is stable and glass fits neatly into its plastic frame. Replace any door bins you removed.
Ta da!
This is your last chance to clear all the walls, floor, and ledges at the bottom of your fridge. Just sayin'.
Put new shelf upside down on counter. Transfer metal rod to new shelf, screw it in. Transfer hinged drawer covers. Transfer textured plastic topic pieces, again putting one side (of each) in first and flexing unit a little to get other side in. Turn right side up and angle back into refrigerator.
Bring shelf flat and push to the back of the refrigerator until it is flush with the back. Lower whole unit until it rests on top of the side rails where drawers slide in. Left side has a tongue that will fit into a 2" or so notch near the front, right side will rest on top of a round bumper. Front coldness control should still operate smoothly. Put drawers in to make sure they glide and close smoothly. Put glass shelf on top and press down lightly to make sure lower shelf is stable and glass fits neatly into its plastic frame. Replace any door bins you removed.
Ta da!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- shirley from ONALASKA, WI
- Parts Used:
- 6600JB1010A
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Light switch for refrigerator not functioning
Followed instructions online
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Art from GARNER, NC
- Parts Used:
- 6871JB1423N
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Lights stayed on when doors were closed.
Verified that the contact switches were good. Issue was in the main board. Pulled fridge out from wall. Unplugged fridge from wall socket.
Took out 3 screws holding cover of main board. Unplugged main board. Replaced main board and reconnected plugs to main board. Replaced cover with 3 screws. Pushed fridge back against wall.
Took out 3 screws holding cover of main board. Unplugged main board. Replaced main board and reconnected plugs to main board. Replaced cover with 3 screws. Pushed fridge back against wall.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jane from SHORELINE, WA
- Parts Used:
- 6600JB1010A
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Door switch would not turn on interior refrigerator light.
I had previously watched a YouTube video (do this first!!) on a similar Kenmore model so I knew what to look out for: (1) turned off power, (2) took thin putty knife to slip under outer lip of switch (most screwdrivers are too thick), (3) wiggled switch at front end to release the tab, (4) unplugged from the socket, (5) plugged in new switch, (6) popped new switch back into door, (7) turned on power. Voila !! Super easy. I couldn't believe it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephen from DICKINSON, TX
- Parts Used:
- MDS38201426
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Freezer door gasket needed replacing.
Simply removed old gasket. Started in a corner with installing the new gasket. It went in easily and quickly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Maryann from BROOKFIELD, IL
- Parts Used:
- MDS38201426
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Icing up in the freezer due to poor gasket
Watched a couple of YouTube videos and then went at it
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Philip from Ashland, MA
- Parts Used:
- 6600JB1010A
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Lights didn't come on when door was opened
I have moderate to good mechanical skills, but getting the old switch out was a sizeable challenge. Since this switch suffered some damage during extraction, I was lucky to have ordered a new one to replace it. Reinstall took approximately 90 seconds. PartSelect saved me an expensive service call.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from STEPHENVILLE, TX
- Parts Used:
- AEC73877601
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Broken freezer rail.
Took out tray , removed 2 screws, removed old rail and installed new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Greg from CASA GRANDE, AZ
- Parts Used:
- 6600JB1010A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
door slight switch failed
Covered the sidewall with tape to protect. Pried the switch out with knife blade and removed electric plug with needle nose pliers. placed plug in new switch and pushed switch into the hole in the side wall. Took about five minutes.
Was this instruction helpful to you?
Thank you for voting!