LFC25760SB (00) LG Refrigerator - Instructions

Super easy. Removal of old shelf and 3 screws was obvious how to put in new shelf. Thank you. Excellent cost, delivery and ease of transaction.

Access to the main PCB is at the back of the fridge. Once the cover plate is off, notes were made of the cable connections though not truly necessary as the cable connectors are almost all at different sizes. Sharp nose pliers made removal of the connectors way easier. The new board fixed the problem as advertised.

Cover the putty knife with tape so you do not scratch the side wall where the switch is located. Slide the knife under the edge of the switch and push in a bit towards the switch and slightly twist to pop the switch out of its hole. Disconnect the wires from the switch and simply plug in the new switch. Push wiring back into the hole and careful push the switch into the hole until it snaps into place.

Removed the cover 2 screws
Squeezed the 2 side sleeves and removed
Snapped in new button, replaced the cover. Done

My son just pried out the old switch with a screw driver snapped out the old one and snapped in the new one. Pretty sure even I could have done this. Very quick and easy. Thanks. :-)

Remove door seal and cam shaft (one piece). Remove broken cam by removing Philips head screw. Replace broken cam with new cam and reassemble. The actual repair took about 15 minutes however the majority of time was spent figuring out that the door seal and cam shaft had to be removed, no tools required.

Unplugged the fridge. Used a screwdriver to loosen the switch. Easy to disconnect from fridge and just plugged the new switch in. Popped right back into the side of the fridge and worked perfectly.

i first replaced valve as the water line hung up and broke the valve as i was moving fridge out,be careful about doing this,now i need to replace icemaker as its not working,ps it wasnt the water valve ,i broke it,so first replaced it now icemaker ,lg stinks for the 2 yrs icemaker has worked,my previous kenmore icemaker thru door worked for 23 yrs and was working the day i replaced it, the new electronic appliances are nice when they work!!!>Marvin

slid screw driver under edge of switch, easy.

I popped the old switch out of place and then disconnected the wire harness from the switch with a pair of needle nose pliers. I then inserted the harness into the new switch and popped the switch into place. Super easy and fast.

Replacement part from PartSelect was OEM, identical to original part. Installation was very quick. Inserted hinge on left side and then depressed the right side to slip it into place. Presto, it was done. Most impressed with PartSelect on the OEM replacement part and very prompt delivery.

Removed white plastic trim and installed new latch / cam shaft

The plastic is real weak and the articulation point is not manufactured strong. You have to put one end in a female receiver and flex the tray cover with your fingers crossed hoping it won't snap, while sliding the other side into a similar female receiver on the other side. The Crisper drawer front has not come in yet. Disappointed that you have to buy the entire drawer with a front instead of the front. This is the 2nd one I have replaced. The difference in the Drawer Front...$10.00 and then entire Front and Drawer, $45 plus...

Simply used a flat head screwdriver to get the first few inches of the gasket out of its track and after that just pulled it by hand. New gasket slipped over the door, lined up the corner and pressed into in the track. Checked to see that it was snug all over and we were done. 5 minutes at the very most. Never would have noticed this. Took all the bins out of the freezer to give it a good cleaning and noticed the torn piece hanging. Our refrigerator runs much less often. Expect to see a difference in our electric bill!

Tape off the light button so door alarm does not go off. Take off the clear light shield and remove the light bulbs. Be careful, bulbs may still be HOT!! With Phillips head screw driver unscrew the light plate assy. Drop it down in a comfortable position. Disconnect the connector, unscrew the thermal sensor and remove light assy. Install new light assy into light plate assy. There is no thermal senor in the new assy. Snap light plate assy back into place and install the two screws previously taken out. Install bulbs and clear cover. Remove tape from light door switches and you are done. Lights should go on and off when door buttons are pushed in and out.