LFC20740ST (ASTCLGY) LG Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Lawrence from FALL RIVER, MA
- Parts Used:
- 4620JJ2009A
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Door Stopper had snapped off
Unscrewed what remained from broken door stop, aligned new one, screwed it in. Done!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sidney from ENDICOTT, NY
- Parts Used:
- 6600JB1010A
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The switch became intermittent - Possibly a poor designe
Used a small screw driver inserted into the front of the switch (facing the front) and pried until the switch was coming out. When out, I removed the connect harness and replace the switch with a new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JON from OJAI, CA
- Parts Used:
- 6600JB1010A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
INTERIOR DOOR ACTIVATED LIGHT SWITCH QUIT WORKING
1. Unplug the refrigerator (to avoid shock) 2. With one screwdriver pry open the switch on the side facing the door to a gap of about 1/8 inch 3. Insert a second screwdriver into the gap to press the plastic tab back slightly and this should release the part. 4. pull the part out and unplug it, you may have to pry back some small tabs on the sides, 5. Plug in the new switch 6. plug in the refrigerator the light should come on, if not tighten the connection 7. Insert new switch back into its slot, it should snap in place. Done!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jesse from Pella, IA
- Parts Used:
- AJU55759303
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
Not making ice but could hear the solenoid trying to work
I turned off the water supply. Took off the access panel at the bottom of the fridge. Disconnected the waterlines from the valve. Remove the screw hole in the valve in place install the waterlines on the new valve attach the new valve to the refrigerator, reinstalled the back panel turn on the water And it made ice.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rita from GROSSE PT PK, MI
- Parts Used:
- 3551JJ1005X
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
Crisper cover broke.
It took me about 20min. Remove glass top and remove old support. Slide new support and glass.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cathrine from NEW ORLEANS, LA
- Parts Used:
- MEG54557902
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
The right hand glide for the top freezer drawer was broken.
Replaced the glide.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Greg from CASA GRANDE, AZ
- Parts Used:
- 6600JB1010A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
door slight switch failed
Covered the sidewall with tape to protect. Pried the switch out with knife blade and removed electric plug with needle nose pliers. placed plug in new switch and pushed switch into the hole in the side wall. Took about five minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from CURWENSVILLE, PA
- Parts Used:
- 6600JB1010A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Door light switch, 3rd one I have replaced in 6 years made in China.
Easy install, small screwdriver under back of old switch push out and pull out with small pliers. unsnap the old plug and install new. YOUR DONE
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dean from HILLSDALE, MI
- Parts Used:
- 6600JB1010A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Replace switch
Read previous tips
Taped off area around switch to protect surface
Used putty knife to extract switch
Used screwdriver to separate connector from switch
Plugged in connector
Pushed switch assembly into opening
Removed tape
Taped off area around switch to protect surface
Used putty knife to extract switch
Used screwdriver to separate connector from switch
Plugged in connector
Pushed switch assembly into opening
Removed tape
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gabriel from SACRAMENTO, CA
- Parts Used:
- EBR36222901
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Refrigerator no longer had power
Refrigerator seemed to have lost power. compressor wasn't on and no lights were on. Cricuit breaker checked out ok. Traced power with a voltage sensor to the main board on the back of the Fridge. Had power all the way to the PCB Assembly. Removed PCB board using pliers to pinch the mounting points. installed new board and reconnected all wires. Very easy. Fridge turned on after that. Success.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Karyn from DURHAM, NH
- Parts Used:
- 6600JB1010A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Replace the light switch for the refrigerator
Cover the putty knife with tape so you do not scratch the side wall where the switch is located. Slide the knife under the edge of the switch and push in a bit towards the switch and slightly twist to pop the switch out of its hole. Disconnect the wires from the switch and simply plug in the new switch. Push wiring back into the hole and careful push the switch into the hole until it snaps into place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from TULLY, NY
- Parts Used:
- 6600JB3007E
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
Left door when opened the light wouldn’t come on. Checked the light, ok. Ordered push button switch
Removed the cover 2 screws
Squeezed the 2 side sleeves and removed
Snapped in new button, replaced the cover. Done
Squeezed the 2 side sleeves and removed
Snapped in new button, replaced the cover. Done
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ilene from Lincoln, NE
- Parts Used:
- 3391JJ2004G
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
drawer was broken and replaced it
Just put the drawer in and it was ready to go. Like those kind of repairs
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alma from Winterport, ME
- Parts Used:
- 6600JB1010A
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
the light did not work when door was opened. At first it would flicker then off completely.
My son just pried out the old switch with a screw driver snapped out the old one and snapped in the new one. Pretty sure even I could have done this. Very quick and easy. Thanks. :-)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Frank from Lawrenceville, GA
- Parts Used:
- 5220JB2010T
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Wrench (Adjustable)
My ice-maker was making almost no cubes
Pulled the fridge out of its space. Removed a metal shield which covered the bottom 12" of the fridge with a Philips head screw driver. The water valve is on your right. turned off the water to the supply line. Removed the supply line using an adjustable wrench. Removed the water line gong from the pump into the fridge. It is held on with a "C" clip which can be pulled off with needle-nose pliers. Removed the old pump, held with one Philips head screw. Then installed the new pump, reconnected the lines, replaced the metal shield and turned the water back on. Vacuumed the fridge and its space before cleaning up. The ice-maker now works perfectly.
Was this instruction helpful to you?
Thank you for voting!