LBC22520ST (00) LG Refrigerator - Instructions

Part Select folks are very professional & courteous. They can only identify the replacement I needed based on data from LG. The data is WRONG. LG should be billed by Parts Select for their valuable time & shipping expenses. What I did was take the old shelf assy with rails & insert 2 each 1/4 - 20 threaded rods into existing holes in the rear of the shelf with nuts & lock washers on the inside & outside of each rail to stabilize it. It facilitated adjustment required to keep the rails parallel so the meat box would be secure. 85 year old guys shouldn't have to do this. LG should do a better job of servicing their product throughout its anticipated life expectancy. They should also send me the proper part.

Used a screwdriver to take off broken clip and then used same screwdriver to replace with new clip. Very easy.

I had previously watched a YouTube video (do this first!!) on a similar Kenmore model so I knew what to look out for: (1) turned off power, (2) took thin putty knife to slip under outer lip of switch (most screwdrivers are too thick), (3) wiggled switch at front end to release the tab, (4) unplugged from the socket, (5) plugged in new switch, (6) popped new switch back into door, (7) turned on power. Voila !! Super easy. I couldn't believe it.

I removed the old water valve, disconnected the water tube going in and tube going out to the back of the refrigerator. New water valve bracket different than the previous one which resulted in my having to modify it to fit. Not an easy task as it was preformed metal. Once hooked up, water turned on, and ice maker turned on, the sound I'm getting now is clunking and not making ice. My debate is whether or not to purchase a new ice maker or revert to the tried and true method with ice trays which work every time.

Used a screwdriver to remove covers. Used a blow dryer to defrost coil in freezer. Cut zip tie and removed old controller assembly. Inserted new controller assembly and secured with zip tie. It took 24 hours for the fridge to cool completely. Now it works fine.

Very easy . Took out old in with new.
Dimensions provided by this site were exact

I took a very thin bladed screwdriver and took the old part out -carefully.
The new part fit in quite easily.

Just slid out the broken drawer and slid in the new one. The web site was very user friendly and my drawer arrive in only a few days. THANK YOU SO MUCH!!!!

1. Pull out the old gasket & push in the new one!

2. Pop out the light assembly with a screwdriver, disconnect the wire bracket, (the hardest part so I used pliers to grip the plastic) and connect the new one...pay attention to the direction to put it back in the space and you’re done! IF I CAN DO IT, YOU CAN DO IT! (Also check you tube videos for accurate instructions & correct terminology!!!)

Pull off the grill cover and remove the 2 screws from the old part and simply screw in the new part. Don’t lose the screws there are no new ones with the new part. Replace cover.

Followed instructions online

Bought a new shelf. Bought a center support (new), Put the new center support in the shelf. Removed glass, old shelf and drawers. Replaced the broken shelf by hooking the new one in to existing supports. Replaced glass. Replaced drawers.

Hard time clipping it in

Used a small screw driver inserted into the front of the switch (facing the front) and pried until the switch was coming out. When out, I removed the connect harness and replace the switch with a new one.

1. Unplug the refrigerator (to avoid shock) 2. With one screwdriver pry open the switch on the side facing the door to a gap of about 1/8 inch 3. Insert a second screwdriver into the gap to press the plastic tab back slightly and this should release the part. 4. pull the part out and unplug it, you may have to pry back some small tabs on the sides, 5. Plug in the new switch 6. plug in the refrigerator the light should come on, if not tighten the connection 7. Insert new switch back into its slot, it should snap in place. Done!