72062 (ASWCSE2) LG Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Ron from MAXWELL, IN
- Parts Used:
- AEQ73110205
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
old one broke
Sent for replacement,got it took old one off put new one on that was it. Thank you
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from DICKINSON, TX
- Parts Used:
- AEQ73110205
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
ICE MAKER STOP WORKING AND MAKING A LOT OF NOISE WHEN TRYING TO DUMP AND WAS HANGING UP TOOK IT APART AND FOUND THE WORM GEAR WAS STRIPED
EASY PEASEY WATCHED INSTALL VIDEO NO PROBLEMS WORKING GREAT THANK YOU
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bob from Phoenix, AZ
- Parts Used:
- AEQ73110205
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Ice would not fall
Replaced Ice maker unit
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from CHULA VISTA, CA
- Parts Used:
- ADX72930460
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Left side gasket was torn and would seal properly
Took off the French door Mullen by unscrewing middle area. Unconnected the wires for the door sensor. Then detached old gasket and replaced with new gasket. Reattached the wiring and snapped Mullen flap in place and finally rescrewed to the door. Seal is very good now.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bryan from ADA, MI
- Parts Used:
- AEQ73110205
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Ice maker not making ice, ice tray overfills and cannot dump, ice sticks together and will not dispense
This repair is pretty straight forward. Just remove the 3 screws that hold the ice maker and bin assembly in, unplug the wire harness connector, then remove it from the refrigerator door. Once removed you simply need to remove 3 more screws that hold the ice maker to the auger/bin frame, remove the temp sensor, and a couple pieces of tape. Re-assemble the new ice maker in reverse order and you are all set. I think part of the issue I was having was due to mineral buildup in the tray as well so it had a hard time cracking and removing the ice. Not sure why it was overfilling, maybe the sensor was broken or had buildup on it as well. This solved all the problems I was seeing and now it makes great ice that doesn't stick together and form a bridge in the bin.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Craig from SPRING HILL, FL
- Parts Used:
- MDS38201426
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Ice crystals appearing on the face of the freezer draws
Part Select had a great video which made the repair easy, using a putty knife to start removing the freeze door gasket. Once removed the install is simple just snap the new gasket into the track, but start at the corner. Other company's have a video requiring you to remove the entire freezer compartment out of the appliance, unnecessary waste of time and labor.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Maryann from BROOKFIELD, IL
- Parts Used:
- MDS38201426
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Icing up in the freezer due to poor gasket
Watched a couple of YouTube videos and then went at it
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephen from DICKINSON, TX
- Parts Used:
- MDS38201426
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Freezer door gasket needed replacing.
Simply removed old gasket. Started in a corner with installing the new gasket. It went in easily and quickly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steve from MUKWONAGO, WI
- Parts Used:
- EAU59551204
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Ice chute would not open.
Removed ice dispenser and display with small screwdriver from front of the fridge. Pried out the whole piece slowly. This exposed the motor that activates the chute. Plugged in the new motor before any removal to verify the motor was the problem. When it worked, removed old and installed new. 3 screws. Piece of cake.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lee from BELTON, TX
- Parts Used:
- EAU60783827
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Ice maker needed replaced
Removed 4 screws then removed ice maker unit. Unplugged the old unit. Checked and verified the inlet tube was clean and not blocked. Plugged in the new unit. Placed unit into proper location and verified it was properly in place. Replaced the 4screws. Turned on the unit closed the ice door and it started making ice maybe an hour later by morning the ice bucket was full. Super easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Elizabeth from Huntington Beach, CA
- Parts Used:
- AAP73252302
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The door bin cracked and broke.
I just popped out the broken bin and slid the new one into the slots on the door.
The fix was easy. I appreciate the expert advice on which part to purchase, as that was difficult to figure out. I received a prompt response to my question and the replacement part came quickly.
The fix was easy. I appreciate the expert advice on which part to purchase, as that was difficult to figure out. I received a prompt response to my question and the replacement part came quickly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Larry from SANTA ROSA, CA
- Parts Used:
- AAP73252302
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Replaced cracked refrigerator door shelvers
Slid the replacement shelves into place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kip from RICHMOND, VA
- Parts Used:
- AAP73252302
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Ordering the right parts
I ordered the needed parts, the correct ones I thought, but when they arrived, I realized they were the wrong parts shipped to me. The reason the wrong parts were shipped to me was because PartsSelect failed to advise me there were none of the parts I needed available so they shipped the left hand basket assembly, door, versus the desired right hand basket assembly, door. I then had to return the wrong parts shipped to me, at my cost of ~$25, and await a refund for the wrong parts originally shipped to me. That's how I did the repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- WES from SOUTHLAKE, TX
- Parts Used:
- ACQ85428602
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
Cracked crisper tray unit cover assembly
Remove glass cover, take out both humidity and air tight crisper drawers, then remove the cover assembly.
Reassemble with new cover
Reassemble with new cover
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Victor from CLARKESVILLE, GA
- Parts Used:
- CSP30021077
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
fridge just quit. No lights ,ice, water or cooling
Called a local repair shop to get the problem diagnosed. Nice repair guy came out and was pretty confident that it was the main board . However his supplier had it on backorder and had a 7 day shipment estimate. When he told me I got on the internet and parts select had the part in stock with a 2-3 business day arrival. I rolled the dice and ordered it. Came the next day via Fed x. It took me 15 minutes to put it in and so far so good. Without the diagnosis I would have been in the dark as to what was wrong so it was worth the fee for the service call to get an expert diagnosis
Was this instruction helpful to you?
Thank you for voting!