70323 (ASTCSE2) LG Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Sonya from VAIL, AZ
- Parts Used:
- AGU75188619
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The spring on the mullion door broke for the last time
This was an incredibly easy repair! 1 phillips screwdriver and two screws. Disconnect the small adapter, and you are good to go!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brenda from WEATHERFORD, TX
- Parts Used:
- AGU75188619
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Front Plate Assembly Not Closing Properly
Found the part on Parts Select. Ordered the part, which came quickly. While waiting for delivery. I watched a short video on how to replace this part. I'm a 73 yr. old female, and no trouble at all. I really felt a sense of accomplishment. Thank you Parts Select.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kevin from DADE CITY, FL
- Parts Used:
- MHY62044106
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Left French Door would not close properly
Removed two screws from door and three locking brackets with a small common screw driver. Raised the bracket, slide in the spring, held down the bracket, installed screws and plastic covers. Less than 2 minutes. Easy application no problem with the new spring or ,mullion..
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- MIKE from ATLANTA, GA
- Parts Used:
- AGU75188619
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Spring on old mullion fell out
Replaced with new mullion
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Larry from GODDARD, KS
- Parts Used:
- AEQ73110210
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
The refrigerator ice maker needed replacing
The only tool required was a Phillips screwdriver. I disassembled the old icemaker and unplugged the electrical snap in device. I removed the ground wire. Then reversed the steps in replacing the refrigerator ice maker kit assembly. It took slightly over 30 minutes to remove and replace the ice maker.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from MONTGOMERY, AL
- Parts Used:
- AGU75188619
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Spring broke on Mullion
Watched the video. Took the screws out, unplugged the connection and slid mullion off. Then plugged the new one in, slid it on and attached the two screws.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alan from MADISON, ME
- Parts Used:
- ACQ85930606
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
LED’s we’re not working only 2 we’re lit
Remove 2 screws swing light down a little bit and pull it to front unplug wires . The hard part of job was finding new replacement light, Partselect.com was only sight I could find that had new replacement number and had the light . Other sites including LG site would only tell me the part number on old lights was discontinued 2 of sites said try used appliance dealers
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Johnny from MOUNT OLIVE, AL
- Parts Used:
- AJU72992601
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Leaking
Swapped old one with new one. New one had extra plug not needed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tom from BLUFFTON, SC
- Parts Used:
- ADX73550624
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
Torn door gasket
Pulled old gasket off by hand. New gasket was easy to install by pushing it into molded cutout in refrigerator door.
Very satisfying to have no glitches in the seamless installation.
Very satisfying to have no glitches in the seamless installation.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jodi from WINTER GARDEN, FL
- Parts Used:
- AEQ73110210
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
My ice maker wouldn't release the ice, nothing was frozen and the motor would just bind
I bought the ice assembly motor only, super easy to install, remove the three main screws, lift out assembly, detach the cable. Then remove the screws on the parts, lift the tape, redo everything in reverse and it works flawlessly!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from IMPERIAL, CA
- Parts Used:
- AGU75188619
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Broken spring on flapper door
Unplugged the frig and removed two phillip screws on flapper door of left door... Unplugged the electrical connector and removed flapper...
Picked up new flapper and snapped electrical contractor together... Slid new flapper bar into place and inserted two phillip screws... Job complete in 15 minutes...
Picked up new flapper and snapped electrical contractor together... Slid new flapper bar into place and inserted two phillip screws... Job complete in 15 minutes...
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eugene from ENCINITAS, CA
- Parts Used:
- AEQ73110210
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Ice tray cracked
Removed the old one and replaced with new just remember do your do diligence watch YouTube videos makes repair a lot easier
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JANET from GRAND JCT, CO
- Parts Used:
- AGU75188619
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The spring on the mullion was broken so the mullion would not open to seal the other door.
I am a73 year old woman. If I can do this, anyone can. Super easy. Just watch the online video.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kathryn from Albuquerque, NM
- Parts Used:
- ACQ86549505
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
The cover had cracked
1. Remove all food from the shelf and take out the crisper drawers.
2. Remove the glass and take out the crisper frame.
3. Take the screws out of the frame that are holding the cover frame in place and remove the old cover frame..
4. Install the new cover and replace screws.
5. Re- install the drawers and glass.
( I'm a 76 yr old female and did it myself with the help of the instructions you provided!). Thanks
2. Remove the glass and take out the crisper frame.
3. Take the screws out of the frame that are holding the cover frame in place and remove the old cover frame..
4. Install the new cover and replace screws.
5. Re- install the drawers and glass.
( I'm a 76 yr old female and did it myself with the help of the instructions you provided!). Thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from ELLWOOD CITY, PA
- Parts Used:
- MHY62044106
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
The original spring in the mullion door broke
I disconnected the refrigerator power, removed the 2 screws holding the mullion door on the left side of the refrigerator French-door (it’s the flap that allows the door to close). Removed the broken spring and installed the replacement spring in its place. Reinstalled the mullion door by putting it in place and installing the previously removed screws.
Was this instruction helpful to you?
Thank you for voting!