KBSN602EPA00 KitchenAid Refrigerator - Instructions

At first I went to a local part supplier and they didn't have it in stock but could order it for me for $55.00 plus $10.00 to ship it. I told them I would have to think about it. I went home and got on the computer and found your web site and was I shocked when I saw the same part listed for $6.98 and $7.00 to ship it. You guys saved me $50.00. The part arrived in two day and took 5 min. to install. I now have light in my refrigerator. Thank you.

The first thing I would like to say is thank you Parts select for a very fast delivery. It was within 24 hours I received my component. The installation went very well. The main thing is to take each part off the old mold, one at a time and install it onto the new mold. Make sure to look at each part as it is mounted to the old mold and re install them the exact same way. Just be gentle with some of the plastic pieces because they are fragile in certain areas. It will take a few hours for everything to start working properly. Thanks again Parts select. Good luck and God Bless.

Removal of the Ice Maker required the removal of only one screw from underneath the maker and the power connector disconnect. Dis-assembly was straight forward. Remove old tray and heater, and reassemble with new tray and heater unit. Reinstall Ice Maker! Special Note: Allow the Ice Maker time to cycle through it's sequences. It may take a period of time before it starts producing ice after re-installation.

Remove the ice maker with two screws in the side and one screw in the bottom. You don't have to completely remove the side screws but you do have to remove the bottom screw.
Lift up on the ice maker and reach behind it and unplug the wiring harness. The tube that lets the water in is accessible from the rear of the fridge. Remone the water line, its only finger tight, and remove the two screws. Pull the tube up and out. Thaw it out with hot water and reinstall. With the ice maker out and on the table, pop off the front cover. Remove two phillips head screws and slide the cube tray off. watch how everything is placed before you slide it off. Slide on the new tray and reinstall all screws. Reassemble in reverse order that you took it out. Your ready to make ice...

A very cold and brittle switch in a 17 year old fridge. Used screwdrivers to pry out with some resistance Had to cut the molded plug in half and split wires, because replacement contacts were farther apart than the original. End result, works great.

I noticed that the refrigerator was having trouble maintaining temperature. Thought it might be time for new one until I found out that a new frig was $5k to $7K. Just happened to notice that the light switch didn't look quite right (was not sitting sqaure to the door). Once I pressed it it came loose. I then realized the the lights were staying on (50 watts of heating). Replaced the switch and the frig started working like new.

Unplug appliance. Socket wrench to unscrew two screws. Module drops down. disconnected two press-on wires by prying off with screwdriver. Removed old switch. Press-fit new switch. Reconnected two wires (color coded). Screwed module back in place. Plug in appliance.

Great service. Unpluged old switch and pluged in new one. Works great

Used a screwdriver to pry loose the old switch, swapped wires to the new switch and pushed it into the opening. Took about 2 minutes.

Part was easy to order, delivered quickly, installation very easy. Just unplug the unit, pop out the old swich using a screwdriver, disconnect and reconnect leads and pop switch back in. Definitely recommend that you can do it too.

Pry old switch and pull out. Disconect two wires. Put two wires on new switch, must be inserted right and connections not loose. Put switch in, making shure wies do not come off and snap in place

After disconnecting the electricity. I followed the instructions as indicated in the "HOW TO" article on the website. I used a steel putty knife and pried the light switch out of its retaining hole. I worked the right side the most since this is the side with the retaining clip. After I removed the switch I transferred the two electrical outlets to the new switch and easily snapped it into place. Engaged the electric power and tested the switch.

disconnected el. power to fridge. pried out broken switch with small screwdriner and pulled out w/water pump pliers. installed new switch and pressed into opening.

removed the 2 screws that held the panel in place, had to reach up and push on locking tabs to lower trhe front of the panel. was able to then push on the locking tab of the switch to release it. removed the wires, replaced them onto the new switch, and snapped the switch into place. the rest was reverse of the uninstall process.

I removed the ice maker, saw the problem, took the ice maker apart and ordered a new mold. I reassembled it with the new mold and it now makes ice but the control arm remains up after each ice dump. I plan to take the ice maker back out when we leave (we are snow birds in Florida) and see if the arm is properly placed.