KFIS29BBBL01 KitchenAid Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Ralph from Tequesta, FL
- Parts Used:
- WPW10347093
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Screw drivers
Getting the second part assembled, should have been pre assembled
With a screwdriver and a lot of time
Was this instruction helpful to you?
Thank you for voting!
The lights were out in the part of the refrigerator and freezer section of refrigerator.
I ussed meter to check the voltage levels and they were fine. I refrence a you video on the refrigerator and foud out that the lights are setup in series like christmas tree lights. If the freezer light is out it will affect the rest of the lights in the refrigerator. I removed the freezer light module and test the light by swapping it with a know working light. the freezer light was the culprit that took the lights out in the side panels and the left side of the refrigerator section. I replaced the freezer light and all the lights now work without issue.
One light and they all go out. So i used one fo lights
One light and they all go out. So i used one fo lights
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Don from Orlando, FL
- Parts Used:
- W11168758
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Water was leaking when ice maker or water dispenser was being used.
Looked for the same repair on line by model number. I found it, watched the repair, then used those instructions to complete the repair on my refrigerator. The disassembly and reassembly took longer than actually replacing the part. It now works beautifully with NO leaks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Catherine from BROOMALL, PA
- Parts Used:
- W11396033
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The door switch was broken so the interior light would not come on.
The instructions in the package were not helpful. They wanted me to cut the wiring harness and described where to cut based on the wire colors. My wires were not the same color! I removed the light mechanism using a combination of a screwdriver, putty knife, and plain old muscle with my fingers! The wiring harness unplugged easily and the new one inserted. It was easy to push the whole assembly back into the door. I spent more time looking for something to cut the wiring harness with (and never did find it) than the whole job actually took without needing to cut anything!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from FORT MYERS, FL
- Parts Used:
- W10822606
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Agitator seized because of rust
Replaced motor
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- HARRY from FSTRVL TRVOSE, PA
- Parts Used:
- W11396033
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Freezer drawer light switch failure.
Disconnect plug from wall. Insert putty knife between light switch.and trim panel , apply pressure to depress plastic spring holding switch in place. Apply a slight twist too putty knife releasing switch from trim piece. This wil expose plug connected to switch. Disconnect plug from switch. Connect new switch to plug. Insert switch into trim. Plug refrigerator into wall socket.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donna from Oro Valley, AZ
- Parts Used:
- W11396033
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Light switch on door broke
Popped out broken switch with blunt flat edged instrument. Disconnected switch from unit . Plugged new piece in and reinserted into side panel of refrigerator. Very easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gail from Golden, CO
- Parts Used:
- W11384469
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broke light switch while cleaning
use kitchen knife to pry out. replaced switch assemble and pressed back into place. Could not have done this with out help from previous customers. Thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jason from Roanoke, VA
- Parts Used:
- W10822606
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
Motor stopped working
I thought this was going to be much more difficult than it was. Take the bottom access door off (using a small socket - same size for all screws). Disconnect the plug to the motor. Unscrew the 4 screws holding the motor. Take the motor out. Unscrew the shaft screws on top (only 2) so you can manipulate it if need be up and down or spin it. Insert new motor and make sure shaft is seated correctly into the motor head. Screw motor back in. Screw shaft back in. Plug up motor. Screw bottom door back on. You are done. EASY!! Took me about 10-15 minutes to do. Much easier than most things.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jim from BROADVIEW HTS, OH
- Parts Used:
- EDR2RXD1
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Replace refrigerator water filter
I followed the instructions in the appliance reference manual, and successfully replaced the water filter in 2 minutes, and reset the water quality indicator.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from OLEAN, NY
- Parts Used:
- W10865826
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Wrench (Adjustable)
Water inlet valve leaking
Removed valve, replaced, slight modification needed on water line going into ice maker.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- george from Albuquerque, NM
- Parts Used:
- WPW10347093
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Ice Maker was not crushing ice properly
Simply replaced the Ice Maker container
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Walter from MYRTLE BEACH, SC
- Parts Used:
- W11509548
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Ice dispenser motor not working
I used the video step by step. The video showed complete process to swap out the motor. It was very simple to do.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from AUBURN, CA
- Parts Used:
- W11396033
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Refer lights not working, there are two lights and neither worked. Decided the switch was the problem.
The switch fix but did not fix the problem. I assumed the wires go on the same way as on the old switch. Is it possible if one light Burns out, the other will not work either?
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from RIDGECREST, CA
- Parts Used:
- W10407212
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
Door gasket had deteriorated and needed replacement
Remove torn old gasket.
Starting with bottom slid the gasket retainer under the door retainer lip on bottom. Repeated for top. Slid the retainer under the open side door retainer lip. Then pushed the gasket as much as possible to hing side. The slid the gasket retainer under the door retainer lip.
Starting with bottom slid the gasket retainer under the door retainer lip on bottom. Repeated for top. Slid the retainer under the open side door retainer lip. Then pushed the gasket as much as possible to hing side. The slid the gasket retainer under the door retainer lip.
Was this instruction helpful to you?
Thank you for voting!