KSF22C4CYY00 KitchenAid Refrigerator - Instructions

Small flat head screw driver.Light is basically a computer module with plug connector

I removed the filter from the box I took the old filter out and inserted the new air filter put the cover down and that was it.

Easy repair, unplug the fridge and then remove the 3 screws on each side of the freezer holding the emitter and receiver. Swap the boards and re-install. Takes less than 10 minutes.

I did an internet search about the problem and found the information and experience that other people had. Ordered the part and that's it. One important thing to remember is to unplug the power supply of the appliance prior to making any repair. I short circuited the original board when I tried to plug it back in after cleaning the optics. (The board might have been bad before that.) The red light stop working but the frige is making ice non stop!!

Unpluged fridge, removed 3 screws from each control board (1 on left side and 1 on right side in freezer below ice maker compartment, unplugged and swopped out with new ones. Did one side then the other. Learned about the issue from other people on PartsSelect. Coulden't have been easier. Got parts in 2 days. Works like a charm now.

Removed cheese & cold cut drawer accessing lower crisper drawer glass missing from surrounding frame.
Dropped in glass into grove of crisper frame…Reinstalled (sliding)!above cold cut drawer in its position and the same for crisper drawer..Finished!!!
All good except for $110.00 price tag for a piece of glass

Installed new led light plug and play

followed the video provided on website. repair was very simple / straight forward. Once emitter and receiver boards were replaced, issue with ice maker was resolved.

Removed the cover plates and unplugged bad boards. Hard to plug in boards after attached to cover plates. Plug in boards first then attach to mounts. Ice in 4 hours.

Originally I took the module off and found that a small plastic part had broken. Both pieces were still there, so I super glued them together and reassembled the unit. It worked great for a couple months. I realized it needed a more permanent fix, so I found the model # and looked up the part. That was very easy on your website. I ordered the part expecting it to take 4-7 days. It was at my house in two days! 15 minutes later I was makin' ice, and makin' my wife happy. Thank you for an all around great experience. I'll definitely buy from you again.

Shelf slid right in. Perfect!

Slid the old drawer out and slid the new drawer in. Less then a minute!

Placed tray on lower part of refrigerator.

I pulled the wiring harness off the bad motor, removed the fan blades (it was just a press fit and can be pulled off by hand), took out the three screws. The fan on the replacement motor had to be installed out of the fridge. I wiggled the new motor into place and installed the three screws. I cut the wiring harness off the fridge side and cut back the insulation. Using wire nuts I reconnected the wiring. I plugged the fridge back in and it worked like a champ.
The repair went fairly easy. The motor was a bit difficult to get into tight space with my big hands. The wiring harness on the fridge side had to be cut and wire nuts used to reconnect the wiring to the new motor but it was pretty straight forward. Over all the repair was easy except for being in a tight spot. I recommend trying to fix it yourself, you may supprise yourself and save some serious bucks on labor cost to boot.

I first had a technician come out to the house and he wanted to charge nearly $300 to replace the icemaker unit. I told him he was "high" and began doing my own research of the problem. That's when I found this website (thank God!) and read the notes from other customers. I figured out the secret location of the KitchenAid icemaker troubleshooting guide (why they hide this information I have no idea -- it's ridiculous), and performed the diagnostics to determine the exact problem. That is how I discovered that the emitter and receiver control boards were bad and not the icemaker motor module as the technician had tried to tell me. Good thing I didn't pay him, because my icemaker still wouldn't be working! The electronic control boards are a piece of cake to replace -- just 3 screws on each. Be careful with the electronical connectors since they snap in - don't pull on the wires, first unhook the snaps holding the wire connector to the board and then disconnet it. Once I replaced the boards I turned my refrigerator back on and immediately I heard the water running to fill up the icemaker and not much later I heard my first piece of ice hit the bucket. Woohooo!!!! It feels nice to fix a problem myself for a reasonable price. This site rules. I'll be coming here again in the future!!!