KRFF302EBL00 KitchenAid Refrigerator - Instructions

When I received the gasket I laid it out on the floor in a spare room not too far from a heat register to let it straighten out. (If it were summer or sunny weather here I would have laid it out in the sun.) My adult son did the repair - it was very easy to pull out the old gasket and to gently clean the edges with a scraper to prepare for the new install. He followed instructions and other tips but the first section took a while before it would stay inserted. Once it did though, the rest of the gasket snapped in very quickly. I am happy the seal is much improved.

1. Turn your water OFF and pull the refrigerator out from the wall so you can access the back.
2. Use pliers to remove tubing clamp.
3. Remove old water fill tube.
4. I used a putty knife to gently pry out the old fill tube from the back of the refrigerator. Once the fill tube pulls out about 1/4 to 1/2", then you can gently pull the remainder of the tube out by hand. Once I removed my "old" fill tube, that is when I saw the "ice plug" that was causing pressure in the water supply line and caused my water line to pop off.
5. Install new fill tube. The end that goes in first needs to go through a small "ring" inside the freezer (this "ring" is not encountered until the fill tube only has about one more inch to be inserted into the back of the refigerator. I could barely see this "ring" if I opened the freezer drawer and stuck my head in as far as I could. I had to gently rotate the new fill tube until it cleared the "ring". You will feel some resistance until it lines up properly.
6. Snugly push in the part that stays on the outside of the refrigerator until it looks like it is sealed.
7. Gently push up the water fill tube where it belongs in the new part and replace the tubing clamp.
8. Turn your water on and make sure there are no leaks (I left my refrigerator out for about an hour).
9. Push your refrigerator back in place.

Removed the old gasket by pulling it out of the groove and installed the new gasket using my fingers to push the gasket into place.

The repair was pretty simple once we had the new one:

Unpacked new gasket and used a little heat in places to straighten it out.

Removed old gasket
just started at one corner by pulling out of groove and went around the door till all of gasket had been removed from the groove around the door.

Installed new gasket
Inserted into groove on one corner and then went around the door until all of gasket had been inserted.

Closed door and checked that there was good coverage all around the door.

took about 15 min just took off gasket with flat screwdriver cleaned and put it on no glue it has magnets very easy

Took out the bottom drawer, removed one hexhead nut on the unit, unplugged the unit, plugged in the replacement unit, screwed in the hexhead screw, replaced the drawer, that's it! Very user friendly.

Removed old seal and installed new one. Whole job took less than ten minutes. Repair video made it very easy to do! Be sure to allow proper relaxation of new seal before install.

Heated new gasket in dryer. Removed old gasket. Took less than five minutes per door and I am 78 years old!

The part arrived as expected. I detached the existing mullion rail using a socket wrench and disconnected the wires, which was as easy as pulling two pieces apart. Then I connected the wires to the new rail, slid the part into place and used the socket wrench to secure it. As easy as could be and good as new! In total, it took a matter of minutes.

Removed old ice maker by removing 3 screws, unplugged wiring harness. Replaced with new ice maker, placed three screws back to secure the ice maker, plugged wire harness back, and product is working well at this time.

After the original center crisper drawer slide rail broke and and second also looking in deep into your parts catalog I discovered that the refrigerator never came with a crisper frame brace from the store or factory.
Thanks to you , I no longer have the use of the center rail breaking off for now everything is made out of cheaply make plastic by whirlpool.

Very easy-slightly bend the end piece to fit over the peg.

I changed the bulb but it still didn’t work. I ordered a bulb holder and replaced it and it works properly now. It was an easy repair, remove the bulb, gently pry the bulb holder out with a screwdriver and snap the new one in.

It was useful that under the description of the part in the catalog, it showed that this part was often used to repair this issue. The service was great and the delivery was fast.

Simply cut the water tube on both sides of connector and push in the new one.

I first removed the bottom shelf. Then I popped the rail in. It was pretty easy although I did have to use some force to fit it in. Ordering the part and doing it myself was a lot cheaper than calling the repair man.