KRMF606ESS00 KitchenAid Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Mike from WILMINGTON, NC
- Parts Used:
- W10737605, WPW10661886
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
stud screws for handles
easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sung-Su from BISMARCK, ND
- Parts Used:
- W11396033
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Broke the Rocker Switch in Fridge side
Popped out with butter knife and unplugged 3 prong connector and reversed with anew switch.
But, unfortunately it got broken again exactly same way as before.
So, I ordered same switch again for 2nd time.
Maytag should recall that Rocker Switch and build with better materials.
But, unfortunately it got broken again exactly same way as before.
So, I ordered same switch again for 2nd time.
Maytag should recall that Rocker Switch and build with better materials.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Olga from COLLEGE STA, TX
- Parts Used:
- EDR2RXD1
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Filterer
Easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Virginia from POLSON, MT
- Parts Used:
- EDR2RXD1
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
replaced water filter
Had a hard time getting the refridgerator part of the filter to LET GO. The grooves weren't lined up with the areas meant to pinch. A knife on each side got it to release.
Thanks.
Have a good one.
Thanks.
Have a good one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Winston A from Brooklyn, NY
- Parts Used:
- W11384469
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Raplaced switch
Repair went well,took about five to ten minutes to disconnect the power from the fridge removed the defective switch installed the new one ,reconnected the power,,,and Let there be light and there was light!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Hemet, CA
- Parts Used:
- W11384469
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Light switch wasn't working.. As I would close the door I would notice our frig light wasn't going off...
I simply removed the old switch by gently pulling down on the old switch with a screwdriver. When it was about half way out I just gently pulled down on the old switch and it popped out... I removed the two connectors attached to the old switch by pulling on the connectors with a pliers...I tried using my fingers but wasn't able to pull the connectors off so I used pliers. It worked perfectly.. When pulling off the old connectors, make sure you attach the new switch to the same tabs on the new switch... It was very easy to do and took under 5 mins.....The light switch works perfect....P.S. You should unplug the frig while making the connection just in case....Safety first....!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- THOMAS from WILLARD, OH
- Parts Used:
- W11384469
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
defective light switch
inserted a knife between the switch and the plastic interior in order to pop the switch out.
then took off the 2 wires on the old switch put them on the new switch and reinserted the switch into the plastic interior.
then took off the 2 wires on the old switch put them on the new switch and reinserted the switch into the plastic interior.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- anthony from HAVELOCK, NC
- Parts Used:
- W11384469
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
changed the light bulb still would not work so I figured it was the switch sure enough.
I took a chance and ordered a switch that is next to the top of the door. looked for how to remove it easily done in ten minutes works fine last long time.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from WADING RIVER, NY
- Parts Used:
- W10822606
- Difficulty Level:
- Difficult
- Total Repair Time:
- 30 - 60 mins
Ice make auger stopped working
I carefully matched the model number to replacement part cross-reference and ordered the Part.
You-tube instructions were accurate except for the plug wire that prevented removal of the auger motor. It took significant maneuvering to drop the old motor. The new motor fit in better but the male plug configuration did not match the female plug from the refrigerator.
A lot of wasted effort and time as well as expense! What good is matching replacement parts when the replacement is not correct?
You-tube instructions were accurate except for the plug wire that prevented removal of the auger motor. It took significant maneuvering to drop the old motor. The new motor fit in better but the male plug configuration did not match the female plug from the refrigerator.
A lot of wasted effort and time as well as expense! What good is matching replacement parts when the replacement is not correct?
Was this instruction helpful to you?
Thank you for voting!
auger motor was not working in ice maker
I watched some of the you tube videos , the repair went well
just followed the directions the repair took less than 30 mins
just followed the directions the repair took less than 30 mins
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dan from BOURBONNAIS, IL
- Parts Used:
- W10865826
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Wrench (Adjustable)
Leaking water valve
Removed old, installed new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles L from ROSEVILLE, CA
- Parts Used:
- EDR2RXD1
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
No Problem This was a simple replacement of the water filter.
Lower the filter cover on the refrigerator, twist the old filter to remove it, install the new filter by pushing and twisting it, and close the filter door.
Using a pitcher, run water through the new filter until the excess carbon leavings are out then the water is clear and is drinkable
Using a pitcher, run water through the new filter until the excess carbon leavings are out then the water is clear and is drinkable
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Regina from CLINTON, AR
- Parts Used:
- EDR2RXD1
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Not making enough ice
Just open the filter and put it in the slot
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- kathleen from GREEN VALLEY, AZ
- Parts Used:
- W11396033
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
broken light switch in the freezer
We removed the old switch, unplugged it, plugged the new one in and it was easy to do. But when we tried to put the switch back in we had a very hard time doing it. Eventually got it in, but if it had not been for the difficulty we had getting the new switch to snap in to place, it would have taken under 5 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Roseville, CA
- Parts Used:
- W11384469
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Door light switch disintegrated
Very simple fix, remove 3 screws, two connectors to the old switch
Was this instruction helpful to you?
Thank you for voting!