KRMF706EBS01 KitchenAid Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- David from Hemet, CA
- Parts Used:
- W11384469
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Light switch wasn't working.. As I would close the door I would notice our frig light wasn't going off...
I simply removed the old switch by gently pulling down on the old switch with a screwdriver. When it was about half way out I just gently pulled down on the old switch and it popped out... I removed the two connectors attached to the old switch by pulling on the connectors with a pliers...I tried using my fingers but wasn't able to pull the connectors off so I used pliers. It worked perfectly.. When pulling off the old connectors, make sure you attach the new switch to the same tabs on the new switch... It was very easy to do and took under 5 mins.....The light switch works perfect....P.S. You should unplug the frig while making the connection just in case....Safety first....!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Orville from Albuquerque, NM
- Parts Used:
- EDR2RXD1
- Difficulty Level:
- Difficult
- Total Repair Time:
- 30 - 60 mins
Changed water filter. Water came out slowly. took off filter and reinstalled water came out good stream. Ice maker is still not working.
Just stood in front of the refrigerator and disconnected the water filter and replaced it with the new one I purchased from by hand
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles L from ROSEVILLE, CA
- Parts Used:
- EDR2RXD1
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
No Problem This was a simple replacement of the water filter.
Lower the filter cover on the refrigerator, twist the old filter to remove it, install the new filter by pushing and twisting it, and close the filter door.
Using a pitcher, run water through the new filter until the excess carbon leavings are out then the water is clear and is drinkable
Using a pitcher, run water through the new filter until the excess carbon leavings are out then the water is clear and is drinkable
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Regina from CLINTON, AR
- Parts Used:
- EDR2RXD1
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Not making enough ice
Just open the filter and put it in the slot
Was this instruction helpful to you?
Thank you for voting!
POS fridge is constantly under repair.
Understood the problem by removing the old dispenser first. That made me realize I also needed the shaft. Went online and matched up all the #’s and the repair went smoothly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Don from Orlando, FL
- Parts Used:
- W11168758
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Water was leaking when ice maker or water dispenser was being used.
Looked for the same repair on line by model number. I found it, watched the repair, then used those instructions to complete the repair on my refrigerator. The disassembly and reassembly took longer than actually replacing the part. It now works beautifully with NO leaks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Roseville, CA
- Parts Used:
- W11384469
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Door light switch disintegrated
Very simple fix, remove 3 screws, two connectors to the old switch
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from SEGUIN, TX
- Parts Used:
- W11291138
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Repaced the right-side door light switch
Killed the power to the fridge. Then, used a small, thin screwdriver to depress the clip on the bottom of the switch and wriggled the old switch out. The two wires easily came off the contacts with pliers. Connected the wires to the new switch and snapped it into the hole--clip facing down and contacts facing up. Turned the power back on and checked the switch. Worked perfectly! Easy job.
Was this instruction helpful to you?
Thank you for voting!
auger motor was not working in ice maker
I watched some of the you tube videos , the repair went well
just followed the directions the repair took less than 30 mins
just followed the directions the repair took less than 30 mins
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- stu from richmond, VA
- Parts Used:
- W11384469
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
fridge door switch did not work
I removed the switch housing (4 screws), replacing the switch in the housing was a snap. It took 5 minutes, cost $8 and light works like new!
Why didn't I order this part and do the repair earlier? Very simple.
Why didn't I order this part and do the repair earlier? Very simple.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dan from BOURBONNAIS, IL
- Parts Used:
- W10865826
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Wrench (Adjustable)
Leaking water valve
Removed old, installed new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- dorotea from staten island, NY
- Parts Used:
- W11384469
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Light didnt go on
The light rocker switch wasnt working. I found the part on the web site. It was so easy. I used a screw driver to pop out the old one and pop the new one in. It took 5 min. Thanks!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jim from BROADVIEW HTS, OH
- Parts Used:
- EDR2RXD1
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Replace refrigerator water filter
I followed the instructions in the appliance reference manual, and successfully replaced the water filter in 2 minutes, and reset the water quality indicator.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from OLEAN, NY
- Parts Used:
- W10865826
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Wrench (Adjustable)
Water inlet valve leaking
Removed valve, replaced, slight modification needed on water line going into ice maker.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from FORT MYERS, FL
- Parts Used:
- W10822606
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Agitator seized because of rust
Replaced motor
Was this instruction helpful to you?
Thank you for voting!