KSC24C8EYY03 KitchenAid Refrigerator - Instructions

I ussed meter to check the voltage levels and they were fine. I refrence a you video on the refrigerator and foud out that the lights are setup in series like christmas tree lights. If the freezer light is out it will affect the rest of the lights in the refrigerator. I removed the freezer light module and test the light by swapping it with a know working light. the freezer light was the culprit that took the lights out in the side panels and the left side of the refrigerator section. I replaced the freezer light and all the lights now work without issue.

One light and they all go out. So i used one fo lights

Open door and from appliance instruction book
Replace filter

After pulling the fridge out and removing the dust cover over the lower portion in back of the fridge, I could see water dripping from the inlet valve between the water main to the icemaker and the water dispenser in the door.
1. Unplug the fridge
2. Place a towel under the fridge to absorb any over flow
3. Turn off the water supply to the fridge - this is usually at a tap valve on the cold water line. trace the line from the back of the fridge to find the connection point. In the unlikely event there is not valve at the tap valve or if it is inaccessible, turn off the main water supply. If you have to turn off the main supply turn on a faucet somewhere in the house to bleed the pressure from the line.
4. If the valve is tied to the frame or line , undo the tie or cut the zip tie (in my case)
5. Unplug each electric connector from the old valve to the new one.
6. The water connections are all quick connect so release the intake line by pressing down on the white ring and removing the tube. Press the tube into the new valve.
7. Repeat with each line going to the refrigerator making sure to plug each tube into the same outlet you pulled it from
8. In each case to minimize water coming out of the tube, hold your finger over the end while transferring to the new valve.
9. Verify that all tubing ends are FULLY pressed to the valve
10. Turn the water back on slowly and check for leaks. if some are seen turn water back off and repeat steps 6 thru 9.
11. Plug fridge in
12. Run water from the door faucet to bleed any air out
13. Clean up any spillage
14. Replace dust cover (if present) and replace refrigerator in place
Piece of cake

i didn't repair replace capacitor, bi metal defrost thermostat and still not freeze also replace light door switch any suggestion thanks

I was amazed when Fed Ex pulled up to our front door the following day after I ordered the parts, I was wondering what they were delivering and to my amazement it was the parts I had ordered from parts select the previous day , thank you so much , you are awesome. My 73 year old husband who is a 5 year cancer survivor had the part installed and we were ready to start making ice within 1 hour.He went by the installation information sent in by your customers. Thank you all, Jo Mesplay

Removed and disconnected the icemaker, cleaned all areas and disassembled the failed parts. Reassembled with the new parts inlcuded with the purchased package and resinstalled the unit. Started the unit and chedked for proper operation. Successful repair.

Got new part. Removed cover. Tape at top had to be pried loose from door.

Had to turn cup cover from top portion to access power wire. Door and light wires had to be unplugged and moved from clips.

Two screws at bottom removed. Motor unit was freed up and set on table.

Had to remove bottom white section due to light Assembly was not on new section. Removed three screws. Removed three screws from new unit.

Attached old white section with light to new motor unit.

Reattached power wire routed into cup and plugged in. Cup turned clockwise so as to attach.Other wires re-routed and plugged back in.

Cover section screws inserted and reattached.

Turned on/off button back on. Checked all light switches in refrigerator and freezer section to ensure operating. Put bin back in and closed door. No warning lights present. Approximately one hour later, bin had ice in it.

Repair was replacing motor kit. I did not use the plastic parts - ejector arm and separator. Went same as others described. I had removed ice maker from refrigerator although this was not necessary to replace motor unit(Please unplug refrigerator whether or not you remove the entire ice maker).
Removed three screws, removed old motor unit, inserted new unit making sure the ice level wire arm end was in slot. Ejector is D shaped so can't go in wrong. Replaced screws and replaced ice maker in freezer. Note - be sure the water tube is in the trough before trying to refasten ice maker.
Added note: If for whatever reason you need to remove ice maker note that there are three mounting screws (others have mentioned this) Completely remove one under middle of ice maker. For the two at top of ice maker - just loosen a few turns. The ice maker can be lifted and pulled away from the wall without removing these screws. Also there is a tab on the electrical wire connector for ice maker at back wall of freezer. Tab must be depressed with a flat tip screw driver while pulling out to remove wire connector. Tab is on wide side of connector facing inside of freezer.

Repair worked. Have lots of ice again.

Popped out broken switch with blunt flat edged instrument. Disconnected switch from unit . Plugged new piece in and reinserted into side panel of refrigerator. Very easy.

The instructions in the package were not helpful. They wanted me to cut the wiring harness and described where to cut based on the wire colors. My wires were not the same color! I removed the light mechanism using a combination of a screwdriver, putty knife, and plain old muscle with my fingers! The wiring harness unplugged easily and the new one inserted. It was easy to push the whole assembly back into the door. I spent more time looking for something to cut the wiring harness with (and never did find it) than the whole job actually took without needing to cut anything!

Disconnect plug from wall. Insert putty knife between light switch.and trim panel , apply pressure to depress plastic spring holding switch in place. Apply a slight twist too putty knife releasing switch from trim piece. This wil expose plug connected to switch. Disconnect plug from switch. Connect new switch to plug. Insert switch into trim. Plug refrigerator into wall socket.

use kitchen knife to pry out. replaced switch assemble and pressed back into place. Could not have done this with out help from previous customers. Thanks

Pried out old part with screwdriver. Unplugged. When new part came, just plugged it in and pushed the part into place.

The part was perfect, easy installing. The customer service representative was knowledgeable and very helpful.

I just popped out the old switch with a flat head screwdriver. Removed the connections and then installed new switch by reversing steps. Popped in back in and the light went on.