KBBL206ESS00 KitchenAid Refrigerator - Instructions

bulbs were not burnt out. received the new switch in a few days. watch the short video, was good to see how it comes out. used a putty knife to release the defective switch, removed wires put them on the new one and posed the new switch back in. Not bad Part cost $11.00 7 dollars shipping so for 17 bucks it works great. nice to see what is inside the refer!

Put One card in one side and other card on the opposite side, push in on both sides to press in clips that hold light in. Once clips are in light will start to come out unplug light and plug in new light. Push light back in.

Had to push the light switch to get lamp to light up.
Removed power from refrig. and removed old light switch
and replaced with the one I got from Partselect. Turned power back on and was done.

We looked up the problem online with the model number of the refrigerator. We ordered the part and followed the video installation that was sent with the order and was found online prior to purchasing

Eased the putty knife under the edge of the switch housing and pried it off. Pulled two wires off the old terminals and hooked them onto the new one and reinstalled into the refrigerator body.

Easily removed old filter and inserted the new one

My ice maker just stopped filling with water one day and after some troubleshooting, I found that a chunk of ice had built up in the tube between the water supply line and freezer. I took the ice maker out (Don't touch the heating element...it really hurts) and defrosted the ice obstruction by injecting hot water into the tube to melt the ice. I used a new plastic syringe you get with an infant over the counter drug and a bucket to catch the water. I noticed the ice cube mold was peeling and decided to replace the mold. The mold is an easy replacement as long as you remember how you took it apart. My mold had some glue or compound stuck to the side that kept me from getting the mold flush against the motor assembly housing so I had to uncrew and scrape that gunk off and reattached. Other than that, there was nothing to it. Now the ice maker is good for another 8 years.

Removed 4 bottom screws. Removed module screws. Replaced module and motor with new parts (came assembled). Replaced module screws and installed the ice maker with the 4 bottom screws.

Pried out the old switch and installed the new switch.

Tough part was diagnosing the problem: bad water inlet solenoid, frozen inlet line, bad ice maker motor, or door opening sensor? Went to a parts shop & discussed the problem with the serviceman. He said you just need to sequentially replace each part. No way say I, that could cost $300 with a no-part return option.

I decided to replace the motor...Eureka!! It worked.
The underside of the ice maker cartridge has a plastic snap clip on either side of the cartridge. You need push each up, pull the left side of the cartridge out part way & disconnect the electrical connector on the right side(left..you facing the refrig.) With the cartridge out simply remove the 5 screws from the motor plate of the left side & replace with the new one.
Very simple. Slide the cartridge back in the frig. until the 2 snap clips click. Voila...you done! Cost $86..not $300. Apparently the motor is too weak to do the job & burns out quickly. Manufacturer should correct this defect.

pulled oil filter out put new one in maybe 10 minutes

Work just perfect

The best part of the repair was how easy it was to find and order the part. Instead of searching the parts houses around town I just went to the PartSelect web site, quickly found and ordered the part in about five minutes, received the part the next day at my home and was ready to make the repair. Wow! What a pleasure for something to work the way it was meant to. Removed old switch located by prying out with sharp knife or screwdriver. Don't worry about breaking it or cracking plastic. Disconnect(unplug) wires from back of switch. Replace (plug-in) wires on back of new switch. Insert in location of old switch. Finisheed.

Remove the ice maker with two screws in the side and one screw in the bottom. You don't have to completely remove the side screws but you do have to remove the bottom screw.
Lift up on the ice maker and reach behind it and unplug the wiring harness. The tube that lets the water in is accessible from the rear of the fridge. Remone the water line, its only finger tight, and remove the two screws. Pull the tube up and out. Thaw it out with hot water and reinstall. With the ice maker out and on the table, pop off the front cover. Remove two phillips head screws and slide the cube tray off. watch how everything is placed before you slide it off. Slide on the new tray and reinstall all screws. Reassemble in reverse order that you took it out. Your ready to make ice...

The first thing I would like to say is thank you Parts select for a very fast delivery. It was within 24 hours I received my component. The installation went very well. The main thing is to take each part off the old mold, one at a time and install it onto the new mold. Make sure to look at each part as it is mounted to the old mold and re install them the exact same way. Just be gentle with some of the plastic pieces because they are fragile in certain areas. It will take a few hours for everything to start working properly. Thanks again Parts select. Good luck and God Bless.