KRFC300EBS00 KitchenAid Refrigerator - Instructions

The lid that covers the front of the lower meat / produce drawer hinges upward on two small ( easily broken) plasic pins, one on each side of the drawer. One pin is moulded into each "END CAP" that also supports the drawer glides and glass shelf above. The entire end cap must be replaced to repair the hinge. The left side is easy (it's the only one I had to replace); the right side might be more difficult because the right end cap includes a temperature control.
1) Remove the two produce drawers above the lower drawer.
2) Lift off the front glass shelf support, the glass shelf, and the rear glass shelf support from below the two produce drawers.
3) Slide the lower drawer half way out. Remove the drawer lid by disengaging it from the remaining undamaged hinge pin on the OK end cap. Careful not to break the good one.
4) Slide the lower drawer all the way out, then lift up and towards you to remove it from its glides.
5) Using a 1/4" nutdriver or socket, remove the three recessed screws. Leave the drawer glide alone for now.
6) Pull the front of the end cap up and towards you about 3/4" to disengage it from a small retainig button at the top front. Pull the end cap toward you to disengage the two rear retaining fingers.
7) Using a small Phillips screwdriver, remove the drawer glide from the broken end cap and attach it to the replacement end cap. Note which end is the front before removing it.
8) Reassemble in reverse order. Again, be careful with the hinge pins.

Removed the grill and control cover in the top middle of the main compartment, removed the control, unplugged it and put in the new one. The thing that took the longest was figuring out that this was the part that needed replacing. The fridge is less than two years old and about 6 months ago the control started making these odd noises. Now it's quiet. Ah peace!

First I looked at new replacement part, saw what held the part to the frig. Then removed the crisper drawers and vegie drawers and related support pieces. Used socket wrench to take out three screws and started so remove endcap. Realized endcap was attached to a piece that controls air flow to drawer, located supporting screw, removed and entire assembly came right out. I fumbled my way through the linking mechanism being very careful not to force and break anything. Once I figured out how all this worked, it went back together in a few minutes. Replaced the four screws that held the 2 pieces (endcap and airflow) to frig, replace drawer slid, replaced all draws. Done 30 minutes, start to finish. I found Customer Service VERY helpful while ordering piece, couldn't believe it was under $10 and fit exactly! Thanks PartSelect.com!

Perhaps a helpful hint:

When aI received the hose adapter/connector, I inserted the 2 hose ends only to have water drip from the connection.
I used a utility knife to remove an inch from each side, then reinserted the hoses. That made the differnce. Dry as a bone.

LG

Ordered a new filter cover, received in 2 days and installed it in about 5 minutes. Worked perfectly.

Once I saw the replacement part I understood how to pry out the switch with a small screwdriver. Then just unplug the old one, plug in the new one and pop it into place.

The PartSelect site made it easy to correctly identify the correct part, it was inexpensive, and the shipping was fast.

I'm very pleased!

i did not need the can holder in door, we do not buy can drinks. i would rather have the full shelf space, so i replaaced the can holder with a full shelf

Shut down refrigerator at the breaker. Placed freezer items in a cooler. Removed top shelf. You must release roller covers on each side to remove the shelf ( Two front screws must be removed) Took off freezer door. (4 screws holding the door to the bracket) Disconnected ice maker electronic plug. Totally removed bottom screw holding ice maker. Loosen two top screws and remove ice maker. Reverse process to install.

Turned old one until it snapped out. Replaced it with a turn.

I opened the freezer door and peeled out the freezer gasket, inserted the new gasket, and closed the door. I repeated this same process for each of the French doors on the refrigerator. This was very easy to do. The only issue is the replacement gaskets don't seem to have any better stick or magnetic hold than the original gaskets, so I'm not sure the repair will improve the energy efficiency / performance of the appliance.

Turn water and refrigerator off, use hair to thaw the ice maker filler tube, then remove the filler tube inside the freezer. Next remove the water supply line cover plate in back of the refrigerator. Now remove the speed clip at the white pvc elbow and pull out the supply line. Next, grasp the pvc elbow with pliers and pull hard to remove. The new filler tube is a 1 piece design (filler tube and elbow combined) and needs to be cut to the proper length. Mark it inside the freezer, remove it and cut to length. Now coat the outside flange with caulk or PU glue and snap into the opening. Put the speed clip on the elbow first and center it. Ensure that the spreader insert is in place in the plastic tube, then slide the supply line into the elbow untill completely engaged. Replace cover.

Pushed the hinge pins aside and removed the old lid.. Reversed the process to install the new lid

First I removed the drawers above the pantry drawer. Then I took out the pantry drawer. I unsrewed 3 screws that attached the part to the refreg. I then removed the rails that were attached to the part I was repalcing and put them on the new part. I then install the new part. Put the firg back together. It was extremely easy and took about 5 minutes to do.

First, I removed the drawers at the bottom of the fridge and then I removed the three hex head (7/32) screws that hold the end cap on. Then I disengaged the slider which connects to the temperature control for the pantry drawer. Then, unscrewed the drawer slides with a Phillips from the old end cap. Also the slide push rod has to be disengaged from the clips on the back of the endcap.

Then, I reinserted the push rod to the new end cap and reattached the drawer sliders and the slider itself. At this point I realized I SHOULD have unscrewed the temperature slider at the back where it covers the cold air outlet. The screw had slipped out. I replaced it with a slightly larger wood screw. Reinstall the drawers, all done.

Since the crisper didn't come with a front, the old front needed to be removed from the broken cripser and attached to the new one. The easiest way to take off the front is to remove it from the bottom of the crisper. Once the pressure is released it comes off easy. Snap the front on the new crisper by starting with the top and snapping the bottom.