KRBL102ESS00 KitchenAid Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Joseph from Live Oak, FL
- Parts Used:
- WPW10671238
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Rear mount tab broken on Center Crisper Rail
It took longer to empty the glass shelf above the Crisper Bins than to replace the rail. Since the part simply snaps in place, no tools were required
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Julie from BATH, PA
- Parts Used:
- WP67002633
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Cracked humid drawer
Complete replacement of the plastic drawer.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Aquilino O from VALLEJO, CA
- Parts Used:
- 12002355
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers
Freezer temperature goes down to -20*F before compressor stops but refrigerator side remains normal 38*F and compressor makes a grunting noise while running.
Unplug ref then remove lower(freezer) panel plus trays and thermistor’s cover/holder then remove the evaps cover. I found the evaps all frozen up. Cut and remove old thermistor, strip wires 1/2 inch then cut the new thermistor wires to length and strip 1/2 inch, use the enclosed insulated crimp type connector and put back everything in the reverse order. It works great afterwards.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from COAL VALLEY, IL
- Parts Used:
- WP67006878
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
The old shelf shattered when we tried to clean it
Just slipped it in. I think it's a very poor design.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kevin from SWANVILLE, ME
- Parts Used:
- W11338583
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Freezer Bulb failed
Unscrewed bulb from sock .
Replaced with new one . Now working
Replaced with new one . Now working
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from CRESCO, PA
- Parts Used:
- WPW10671238, WP12227303WD
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Center crisper rail breaking off.
After the original center crisper drawer slide rail broke and and second also looking in deep into your parts catalog I discovered that the refrigerator never came with a crisper frame brace from the store or factory.
Thanks to you , I no longer have the use of the center rail breaking off for now everything is made out of cheaply make plastic by whirlpool.
Thanks to you , I no longer have the use of the center rail breaking off for now everything is made out of cheaply make plastic by whirlpool.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Christopher from HOMESTEAD, FL
- Parts Used:
- 12002355
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Top section warm, but freezer okay.
Popped off the control panel at the top behind the door. Found the thermistor and replaced it, cutting the wires and splicing the new one in. Immediately the warm section of the refrigerator was getting below freezing temperature readings, so the cooling vent was not opening. I put the old one back on and the temperature readings went back to being accurate. So this was not the problem. I believe now that the fan somehow is not blowing enough cold air up. So now I'll probably buy a fan motor and maybe a blade and try that. Otherwise the computer module I priced at $500 so I hope it isn't that. I replace the fan motor a few years ago already.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephen from LOVELAND, OH
- Parts Used:
- W11384469
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Light switch lever broke
Unplug refrigerator.
Pry switch out with putty knife
Remove two wires from switch
Attach wires to new switch
Push new switch into slot
Pry switch out with putty knife
Remove two wires from switch
Attach wires to new switch
Push new switch into slot
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gerald from COLORADO SPGS, CO
- Parts Used:
- W10121318
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
ICE BUILD UP AT BOTTOM OF FREEZER
DEFROSTED REFRIGERATOR COILS, BUT DIDN'T REPLACE THE GROMMET.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- anthony from HAVELOCK, NC
- Parts Used:
- W11384469
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
changed the light bulb still would not work so I figured it was the switch sure enough.
I took a chance and ordered a switch that is next to the top of the door. looked for how to remove it easily done in ten minutes works fine last long time.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Miguel from ESCONDIDO, CA
- Parts Used:
- WP67001716
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Ladder hooks broke
Pulled out broken parts and snapped/ pushed into place new ladder hooks 15 min max
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Catherine from BROOMALL, PA
- Parts Used:
- W11396033
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The door switch was broken so the interior light would not come on.
The instructions in the package were not helpful. They wanted me to cut the wiring harness and described where to cut based on the wire colors. My wires were not the same color! I removed the light mechanism using a combination of a screwdriver, putty knife, and plain old muscle with my fingers! The wiring harness unplugged easily and the new one inserted. It was easy to push the whole assembly back into the door. I spent more time looking for something to cut the wiring harness with (and never did find it) than the whole job actually took without needing to cut anything!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joan from SILVERDALE, WA
- Parts Used:
- WPW10671238
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
the rail broke from overloading the drawers
got the new part, took the old part out and snapped the new part in! Very easy. Thank you.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roger from SMITHFIELD, RI
- Parts Used:
- WP12825803
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
I had a loose fitting old condensor fan blade on my new motor.
I made a temporary repair by drilling the old blade plastic hub and put a small screw in it to hold it on to the shaft until the new blade arrived. The new blade came in within the two days I needed before Thanksgiving. I removed the old and pushed on the new. There were 8 screws on the back guard and two to hold the motor on. It was a snap.
Thank you PartSelect.com The wife is very, very happy now, we had 51 coming over for Thanksgiving. :)
Thank you PartSelect.com The wife is very, very happy now, we had 51 coming over for Thanksgiving. :)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- HARRY from FSTRVL TRVOSE, PA
- Parts Used:
- W11396033
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Freezer drawer light switch failure.
Disconnect plug from wall. Insert putty knife between light switch.and trim panel , apply pressure to depress plastic spring holding switch in place. Apply a slight twist too putty knife releasing switch from trim piece. This wil expose plug connected to switch. Disconnect plug from switch. Connect new switch to plug. Insert switch into trim. Plug refrigerator into wall socket.
Was this instruction helpful to you?
Thank you for voting!