KSSS42MDX04 KitchenAid Refrigerator - Instructions

put arm up to stop icemaker from creating new ice cubes. us nut driver to unscrew 3 of the nuts holding icemaker in place do not completely remove the 2 top screws. lift off the screws and unplug from inside wire connection...make sure water tub is removed and frig unplugged. clean off ice anywhere inside freezer...take out new icemaker and connect wire plug...attach icemaker on to the 2 top screws...use nut driver to tighten into place. add and tighten bottom screw...leave arm down...replace clean and dried water tube into back and make sure it slid into ice maker...tighten screws in back and attatch water hose to tube...plug frid back on slide back into place...will start making ice in an hr or so....

The repair was simple.

I first did a diagnosis of the optical cuircuits and found them good. The tray heated up and when resetting the moor controller, the water cyccled to fill the tray so the only other thing it could be was the motor controller.

removed the service door for the ice maker
I removed the wire protectore screw and shroud
pulled the icemaker unit out and unplugged the unit
removed the motor controller end cap
unscrewed 3 screws holding the motor controller
removed and replaced the motor controller. ensured that all wire harness connector poiints were solid
reverse the above instructions and in 5 hours I was getting ice again!

$90 turned out to be a savings from the $250 it would have cost to have someone come out and look at the fridge.

I highly recommend to anyone who can read and use a screwdriver to perform this repair if you have diagnosed this as the root of your problem!

It actually took me longer to think about the repair than actually doing it. It was three screws, two upper that you just loosen and then one on the bottom that you remove. Pulled the unit out and disconnected the power. Slipped the new unit onto the two upper brackets, after connecting the power cord, tightened the bracket screws, reattached the bottom set screw and I was making ice. Incredibly easy. When I ordered the replacement unit they said it would arrive in 3-5 days, but it only took a day and a half. Great experience all the way through. I'm a customer for life.

Removed the one screw holding the unit in place in the freezer and pulled it out. Removed the 3 screws that hold the motor in place on the ice maker. Replaced the motor unit, replaced the 3 screws, and re-installed the ice maker.
Sears wanted $170 for labor for the 10 minute job, plus $130 for the part, which I got here for $65.

The repair was very easy. I ordered the part from Part Seelect and the delivery was very quick.
Opened the box and took out the new ice maker. Emptied the freezer, turned off the power and the water to the Refigerator / Freezer / Iceww Maker. Used a quarter inch nut driver to remove the old ice make. Really easy remove one screw and lewsen two ther screws. unplugged the wiring harness. Took the bale arm off old unit and installed it on the new unit. Check to make sure I had the right wiring harness installed on the ic make which it was. Installed and leveled the new unit. in a little over a hour I had ice. Had to make a few adjustments to the water level setting to make sure all ice cube trays filled up completely.

So easy to do a cave man could do it.

Used a nutdriver and removed the lower mount nut, then loosened the the top two nuts and the icemaker lifted off, then unplugged the device and replugged it into the "old" plug(the new ones were not needed) then remounted it. Then it did not fill (as others posted happened right away.) Some poster suggested manually filling the tray so I did it. Later it froze and emptied and refilled and started working normally. Not sure if putting water had anything to do with it or it just took some time. It would be nice if the instructions addressed this issue.

i followed the online instructions on how to take the icemaker apart, which were very easy to follow. Once the new part arrived it plugged right in and a few steps later it was back together. within the hour we were hearing the sound of ice dropping into the tray. thanks for all the help this definitely saved us money and hopefully we get many more years out of this icemaker.

First I removed the (3) screws holding the unit to the side of freezer wall with a nutdriver. Then I disconnect the Harness from the back of the freezer. You have to work the Harness off connector because it was very tight. The Unit came with the correct harness installed so I reconnected the harness to the Freezer and replaced the (3) screws. I had ice in about 2.5 hours.

removed the three screws holding the old ice maker in place - unpluged the electronics .... took the new ice maker pluged in the electronics screwed in into place and we were in business and had ice within an hour.

First, removed drawer and shelf with flip up lid. Second, removed 4 screws holding track in place and replaced with new part. Reinstalled shelf, flip up lid, and drawer. Easy fix with proper replacement part.

I removed the switch housing (4 screws), replacing the switch in the housing was a snap. It took 5 minutes, cost $8 and light works like new!

Why didn't I order this part and do the repair earlier? Very simple.

It can be a little tricky to snap the piece into place on both sides of the self. The concern is that one might break off the connecting piece. This exactly what I did which led to this repair/replacement part. Patience was key to the success of replacing the rim to the shelf.

Took the old one out in Two Min's, Replaced with the new one in about the same time.
Had ice within 1 hour

Very simple fix, remove 3 screws, two connectors to the old switch

Wathced video (VERY helpful)of how to do repair to make sure it was within my capabilities to do. Made sure I had all requested numbers before ordering. Replacement part was an EXACT fit. 15 minutes of work and I saved nearly $150 of estimate by local service company. I am (and will continue to be) a repeat customer. Thanks. Mel