KSSC48QTS00 KitchenAid Refrigerator - Instructions

Removed the two screws that hold flaping door. Removed the single screw that covers the connecting wires. Disconnected the wiring plug. I wiggled out the ice maker. Took off the motor cover. Swapped out one motor for the other. Reinstalled the icemaker in the resverse order of removal. Note the wiring plug in the freeze is very from. It makine s the reconnection differcult.

Used a screw driver to pull old switch. Pulled one wire at a time, only two wires. After wires instlled to new switch push new one back in place where the old one was.

Bi-metal defrost thermostat tested bad, so replaced. To remove back freezer panel on this model, remove top left and right shelf pegs (use a screw driver). This will let back freezer panel slide up and out.

Control board, located in metal box above the inverter board had a bad 200uF electrolytic capacitor (bulging top) and 12v relay. Replaced all 5 electrolytic capacitors on the board and all 4 relays.

Works good.

Local service person missed the diagnosis and advised $10,000 new refrigerator. I looked and saw that the switch was deformed and had burn marks. Searched for switch online. Found site Ordered. Part arrived next day. 5 minute job to replace. No tools needed. Refrigerator works great. Thank you t!

I simply removed the old switch using 2 small screwdrivers and the old switch case popped out. I then upluged the wires from the old switch and reversed the process. Didn't take longer than 5 minutes begining to end! Thank you for the great service! Duncan quaid

Built-in filter was corroded due to age. New filter corrected problem.

Removed screws, unplugged connectors to the two faulty circuit boards, reconnected both cables to new/replacement circuit boards, reinstalled screws. Extrremely simple! Worked perfectly! Saved about $150 in less than 30 minutes. Great, fast service by PartsSelect.

Easy!!!!! Just cut the power to the unit and unscrew the boards. One is to the right of the ice maker and one is to the left. Snap the connecter on the old board so it will disconnect and replace it. It works perfect now. I had a service man come out and he quoted me $400.00. He told me I needed a whole new ice maker too. Not true. I simply email you guys and had the part in 3 days. It only cost me $80.00. I will use your site for every part I need. Thanks

I called a local appliance repair / sales store and he told me what to look for. There is an electronic "eye" on the "On / Off" panel in the freezer, and there is an electronic eye that sends a beam across to the other side where there is a receiver. If there is no beam, or the beam is obstructed --- for example when the freezer door is open the little "door" on the opposite side of the On / Off switch opens, interrupting the beam --- the icemaker will not work. In my case it was easy... there was no beam being sent across, so I KNEW it was bad.

Ordered the part, took out 6 screws total to remove the sender and receiver, removed the circuit boards with 3 more screws, replaced with new boards, and reinstalled.

Trust me - a 10 year old could do this. Don't be afraid because it involves "circuit boards" - it's literally one or two screws, replace the boards, screw them back in, and plug the two sides back in. ANYONE can do it... anyone!!!

Removed coupling screw and coupling and replaced with new coupling and screw. Check your shaft as well , I didn’t and had to order and wait on IT to arrive before I could complete the job.

First shut off water supply and unplug power. Unscrew icemaker assembly from side wall with 3 screws. Remove front cap and you can clearly see module. Unscrew and remove module ( only three screws). Install new module and revers procedure to finish up. Ice was ready in just a few hours. Video provided by this site was right on and left no questions.

Searched my issue on the internet then chose part select to see if bi-metal thermostat was available and it was so I ordered part which was under $30.00 incl. shipping. I then went to You Tube to watch how to replace the part but most importantly to find out where it was located and degree of difficulty. Replacement was rather simple and it fixed our 22 year old fridge. I must add that when I looked up the part it also told you what percent of the time that particular item actually fixed the problem based on others experience. I thought that was neat info. as I felt better about ordering something that may or may not fix my problem. Thank you,

Remove Ice bucket, Remove Phillips screw from bottom of coupling. replace washer, Coupling and screw. replace bucket. very simple.

We popped out the new filter and replaced the cap with a twist. It was so easy. It is important to vaccum the front of the refrigerator for accumulating dust.

Removed the 2 screws holding the light bulb shield, then the 4 uolding the metal panel. Unplugged the olw door switch and replaced.
reassembled the pieces.