KBRS19KTWH00 KitchenAid Refrigerator - Instructions

Remove 1 screw under ice maker. Gently pull downwards to unhook ice maker. Disconnected 4 pin wire connector. Remove and set aside the cover and wire loop you will need on new ice maker. Reverse the steps to install new maker. Once new ice maker is installed you will have to wait 2-4 hours for ice. There is a thermostat that will need to reach 10 degrees F to operate.

Total time 10 minutes. 9 minutes to clear out the food and 1 minute to install the part. Installation was self evident and could have been done blindfolded. Part just snapped in.

Very easily removed top shel glass above crisper--removed old rail by lifting up--and place new one in slots provided---simple!! Part was delivered in less than 3 days-------very fast and cheap !!!

Repair went well,took about five to ten minutes to disconnect the power from the fridge removed the defective switch installed the new one ,reconnected the power,,,and Let there be light and there was light!

remove parts that were not need installed water valve , ice maker unit and hooked up water supply tested and it works fine. got the parts really quick Thank You

Part received was what I needed. There was one issue--the 'feed' opening to receive water and direct it into the ice tray was a side feed and what I needed was a back feed. That means I had to do some exchanging of parts to make it work. That exercise took more time that the actual installation.

Caused the shelf on my fridge to break a ladder hook. I didn't even know where to begin looking for an Amana refrigerator shelf mount bracket, but luckily found this website from a Google search. The part was super easy to find, arrived in two days, and was a snap to install. What did people do before the internet?

I simply removed the old switch by gently pulling down on the old switch with a screwdriver. When it was about half way out I just gently pulled down on the old switch and it popped out... I removed the two connectors attached to the old switch by pulling on the connectors with a pliers...I tried using my fingers but wasn't able to pull the connectors off so I used pliers. It worked perfectly.. When pulling off the old connectors, make sure you attach the new switch to the same tabs on the new switch... It was very easy to do and took under 5 mins.....The light switch works perfect....P.S. You should unplug the frig while making the connection just in case....Safety first....!!!

After checking the water valves ordered new ice maker. received the part three days after ordering! Clearing out food, removing the old one and installing the new unit took under 15 minutes. Everything went fine.

inserted a knife between the switch and the plastic interior in order to pop the switch out.
then took off the 2 wires on the old switch put them on the new switch and reinserted the switch into the plastic interior.

Bought a new shelf

Take everything off the top self, lift the self install the new part ,put self back in place and then install the drawers again. Took minutes.

I got really tired of taking food out covered in icicles and stabbing a huge block of ice out of the bottom. Turns out all he needed was a little wheel with cogs and I looked up the sticker model number on this site and clicked the part of the fridge. So simple, wish I would’ve done it sooner.

I first removed the icemaker pump and filler tube fron the back of the refrigerator by using an adjustable wrench and pliers. (very simple connection) I went ahead and replaced both items at that time.

Next I opened the bottom freezer and removed the top wire tray and ice container. I removed the bottom nut from the ice maker, pulled the electrical plug lose from the freezer connection. I then just lifted the ice maker upward and off the two screws on the side wall and out it came!

I had a little trouble with the filler tube as it came into the freezer. I had to go back and forth to the back of the refrigerator and freezer a couple of times adjusting the tube, so it woiuld clear the inside freezer wall.

This was a very minor problem. I feel like if I had followed the instructions and made sure the tube came through before attaching the icemaker it would have worked like a charm!

What I really liked, was everything was in the box for the job.

I took a chance and ordered a switch that is next to the top of the door. looked for how to remove it easily done in ten minutes works fine last long time.